Loading...
HomeMy WebLinkAboutContract 60751City Secretary Contract No. 60751 FORT WORTH 4'� - VENDOR SERVICES AGREEMENT This VENDOR SERVICES AGREEMENT ("Agreement") is made and entered into by and between the CITY OF FORT WORTH ("City"), a Texas home rule municipal corporation, and Zone Industries LLC ("Vendor"), each individually referred to as a "party" and collectively referred to as the "parties." 1. Scope of Services. Packaged Pumping System ("Services"), which are set forth in more detail in Exhibit "A," attached hereto and incorporated herein for all purposes.. 2. Term. This Agreement begins on November 20t' 2023 ("Effective Date") and expires on November 20t' 2024 ("Expiration Date"), unless terminated earlier in accordance with this Agreement ("Initial Term"). City will have the option, in its sole discretion, to renew this Agreement under the same terms and conditions, for up to one-year renewal option(s) (each a "Renewal Term"). 3. Compensation. City will pay Vendor in accordance with the provisions of this Agreement, including Exhibit `B," which is attached hereto and incorporated herein for all purposes. Total compensation under this Agreement will not exceed Two hundred forty-nine thousand nine hundred eighty-two Dollars ($249,982.00). Vendor will not perform any additional services or bill for expenses incurred for City not specified by this Agreement unless City requests and approves in writing the additional costs for such services. City will not be liable for any additional expenses of Vendor not specified by this Agreement unless City first approves such expenses in writing. 4. Termination. 4.1. Written Notice. City or Vendor may terminate this Agreement at any time and for any reason by providing the other party with 30 days' written notice of termination. 4.2 Non -appropriation of Funds. In the event no funds or insufficient funds are appropriated by City in any fiscal period for any payments due hereunder, City will notify Vendor of such occurrence and this Agreement will terminate on the last day of the fiscal period for which appropriations were received without penalty or expense to City of any kind whatsoever, except as to the portions of the payments herein agreed upon for which funds have been appropriated. 4.3 Duties and Obligations of the Parties. In the event that this Agreement is terminated prior to the Expiration Date, City will pay Vendor for services actually rendered up to the effective date of termination and Vendor will continue to provide City with services requested by City and in accordance with this Agreement up to the effective date of termination. Upon termination of this Agreement for any reason, Vendor will provide City with copies of all completed or partially completed documents prepared under this Agreement. In the event Vendor has received access to City Information or data as a requirement to perform services hereunder, Vendor Services Agreement Page 1 of 12 OFFICIAL RECORD CITY SECRETARY FT. WORTH, TX City Secretary Contract No. Vendor will return all City provided data to City in a machine readable format or other format deemed acceptable to City. 5. Disclosure of Conflicts and Confidential Information. 5.1 Disclosure of Conflicts. Vendor hereby warrants to City that Vendor has made full disclosure in writing of any existing or potential conflicts of interest related to Vendor's services under this Agreement. In the event that any conflicts of interest arise after the Effective Date of this Agreement, Vendor hereby agrees immediately to make full disclosure to City in writing. 5.2 Confidential Information. Vendor, for itself and its officers, agents and employees, agrees that it will treat all information provided to it by City ("City Information") as confidential and will not disclose any such information to a third party without the prior written approval of City. 5.3 Public Information Act. City is a government entity under the laws of the State of Texas and all documents held or maintained by City are subject to disclosure under the Texas Public Information Act. In the event there is a request for information marked Confidential or Proprietary, City will promptly notify Vendor. It will be the responsibility of Vendor to submit reasons objecting to disclosure. A determination on whether such reasons are sufficient will not be decided by City, but by the Office of the Attorney General of the State of Texas or by a court of competent jurisdiction. 5.4 Unauthorized Access. Vendor must store and maintain City Information in a secure manner and will not allow unauthorized users to access, modify, delete or otherwise corrupt City Information in any way. Vendor must notify City immediately if the security or integrity of any City Information has been compromised or is believed to have been compromised, in which event, Vendor will, in good faith, use all commercially reasonable efforts to cooperate with City in identifying what information has been accessed by unauthorized means and will fully cooperate with City to protect such City Information from further unauthorized disclosure. 6. Right to Audit. Vendor agrees that City will, until the expiration of three (3) years after final payment under this Agreement, or the final conclusion of any audit commenced during the said three years, have access to and the right to examine at reasonable times any directly pertinent books, documents, papers and records, including, but not limited to, all electronic records, of Vendor involving transactions relating to this Agreement at no additional cost to City. Vendor agrees that City will have access during normal working hours to all necessary Vendor facilities and will be provided adequate and appropriate work space in order to conduct audits in compliance with the provisions of this section. City will give Vendor reasonable advance notice of intended audits. 7. Independent Contractor. It is expressly understood and agreed that Vendor will operate as an independent contractor as to all rights and privileges and work performed under this Agreement, and not as agent, representative or employee of City. Subject to and in accordance with the conditions and provisions of this Agreement, Vendor will have the exclusive right to control the details of its operations and activities and be solely responsible for the acts and omissions of its officers, agents, servants, employees, Vendors, and subcontractors. Vendor acknowledges that the doctrine of respondeat superior will not apply as between City, its officers, agents, servants and employees, and Vendor, its officers, agents, employees, servants, contractors, and subcontractors. Vendor further agrees that nothing herein will be construed as the creation of a partnership or joint enterprise between City and Vendor. It is further understood that City will in no way be considered a Co -employer or a Joint employer of Vendor or any Vendor Services Agreement Page 2 of 12 City Secretary Contract No. officers, agents, servants, employees, contractors, or subcontractors. Neither Vendor, nor any officers, agents, servants, employees, contractors, or subcontractors of Vendor will be entitled to any employment benefits from City. Vendor will be responsible and liable for any and all payment and reporting of taxes on behalf of itself, and any of its officers, agents, servants, employees, contractors, or contractors. Liability and Indemnification. 8.1 LIABILITY - VENDOR WILL BE LIABLE AND RESPONSIBLE FOR ANY AND ALL PROPERTY LOSS, PROPERTY DAMAGE AND/OR PERSONAL INJURY, INCLUDING DEATH, TO ANY AND ALL PERSONS, OF ANY KIND OR CHARACTER, WHETHER REAL OR ASSERTED, TO THE EXTENT CAUSED BY THE NEGLIGENT ACT(S) OR OMISSION(S), MALFEASANCE OR INTENTIONAL MISCONDUCT OF VENDOR, ITS OFFICERS, AGENTS, SERVANTS, EMPLOYEES, CONTRACTORS, OR SUBCONTRACTORS. 8.2 GENERAL INDEMNIFICATION - VENDOR HEREBY COVENANTS AND AGREES TO INDEMNIFY, HOLD HARMLESS AND DEFEND CITY, ITS OFFICERS, AGENTS, SERVANTS AND EMPLOYEES, FROMAND AGAINST ANYAND ALL CLAIMS OR LAWSUITS OFANYKIND OR CHARACTER, WHETHER REAL OR ASSERTED, FOR EITHER PROPERTYDAMAGE OR LOSS (INCLUDINGALLEGED DAMAGE OR LOSS TO VENDOR'S BUSINESS AND ANY RESULTING LOST PROFITS) AND/OR PERSONAL INJURY, INCLUDING DEATH, TO ANY AND ALL PERSONS, ARISING OUT OF OR IN CONNECTION WITH THIS AGREEMENT, TO THE EXTENT CAUSED BY THE NEGLIGENT ACTS OR OMISSIONS OR MALFEASANCE OF VENDOR, ITS OFFICERS, AGENTS, SERVANTS, EMPLOYEES, CONTRACTORS, OR SUBCONTRACTORS. 8.3 INTELLECTUAL PROPERTY INDEMNIFICATION — Vendor agrees to defend, settle, or pay, at its own cost and expense, any claim or action against City for infringement of any patent, copyright, trade mark, trade secret, or similar property right arising from City's use of the software and/or documentation in accordance with this Agreement, it being understood that this agreement to defend, settle or pay will not apply if City modifies or misuses the software and/or documentation. So long as Vendor bears the cost and expense of payment for claims or actions against City pursuant to this section, Vendor will have the right to conduct the defense of any such claim or action and all negotiations for its settlement or compromise and to settle or compromise any such claim; however, City will have the right to fully participate in any and all such settlement, negotiations, or lawsuit as necessary to protect City's interest, and City agrees to cooperate with Vendor in doing so. In the event City, for whatever reason, assumes the responsibility for payment of costs and expenses for any claim or action brought against City for infringement arising under this Agreement, City will have the sole right to conduct the defense of any such claim or action and all negotiations for its settlement or compromise and to settle or compromise any such claim; however, Vendor will fully participate and cooperate with City in defense of such claim or action. City agrees to give Vendor timely written notice of any such claim or action, with copies of all papers City may receive relating thereto. Notwithstanding the foregoing, City's assumption of payment of costs or expenses will not eliminate Vendor's duty to indemnify City under this Agreement. If the software and/or documentation or any part thereof is held to infringe and the use thereof is enjoined or restrained or, if as a result of a settlement or compromise, such use is materially adversely restricted, Vendor will, at its own expense and as City's sole remedy, either: (a) procure for City the right to continue to use the software and/or documentation; or (b) modify the Vendor Services Agreement Page 3 of 12 City Secretary Contract No. software and/or documentation to make it non -infringing, provided that such modification does not materially adversely affect City's authorized use of the software and/or documentation; or (c) replace the software and/or documentation with equally suitable, compatible, and functionally equivalent non -infringing software and/or documentation at no additional charge to City; or (d) if none of the foregoing alternatives is reasonably available to Vendor terminate this Agreement, and refund all amounts paid to Vendor by City, subsequent to which termination City may seek any and all remedies available to City under law. Assignment and Subcontracting. 9.1 Assignment. Vendor will not assign or subcontract any of its duties, obligations or rights under this Agreement without the prior written consent of City. If City grants consent to an assignment, the assignee will execute a written agreement with City and Vendor under which the assignee agrees to be bound by the duties and obligations of Vendor under this Agreement. Vendor will be liable for all obligations of Vendor under this Agreement prior to the effective date of the assignment. 9.2 Subcontract. If City grants consent to a subcontract, the subcontractor will execute a written agreement with Vendor referencing this Agreement under which subcontractor agrees to be bound by the duties and obligations of Vendor under this Agreement as such duties and obligations may apply. Vendor must provide City with a fully executed copy of any such subcontract. 10. Insurance. Vendor must provide City with certificate(s) of insurance documenting policies of the following types and minimum coverage limits that are to be in effect prior to commencement of any Services pursuant to this Agreement: 10.1 Coverage and Limits (a) Commercial General Liability: $1,000,000 - Each Occurrence $2,000,000 - Aggregate (b) Automobile Liability: $1,000,000 - Each occurrence on a combined single limit basis Coverage will be on any vehicle used by Vendor, or its employees, agents, or representatives in the course of providing Services under this Agreement. "Any vehicle" will be any vehicle owned, hired and non -owned. (c) Worker's Compensation: Statutory limits according to the Texas Workers' Compensation Act or any other state workers' compensation laws where the Services are being performed Employers' liability Vendor Services Agreement Page 4 of 12 City Secretary Contract No. $100,000 - Bodily Injury by accident; each accident/occurrence $100,000 - Bodily Injury by disease; each employee $500,000 - Bodily Injury by disease; policy limit (d) Professional Liability (Errors & Omissions): $1,000,000 - Each Claim Limit $1,000,000 - Aggregate Limit Professional Liability coverage may be provided through an endorsement to the Commercial General Liability (CGL) policy, or a separate policy specific to Professional E&O. Either is acceptable if coverage meets all other requirements. Coverage must be claims -made, and maintained for the duration of the contractual agreement and for two (2) years following completion of services provided. An annual certificate of insurance must be submitted to City to evidence coverage. 10.2 General Requirements (a) The commercial general liability and automobile liability policies must name City as an additional insured thereon, as its interests may appear. The term City includes its employees, officers, officials, agents, and volunteers in respect to the contracted services. (b) The workers' compensation policy must include a Waiver of Subrogation (Right of Recovery) in favor of City. (c) A minimum of Thirty (30) days' notice of cancellation or reduction in limits of coverage must be provided to City. Ten (10) days' notice will be acceptable in the event of non-payment of premium. Notice must be sent to the Risk Manager, City of Fort Worth, 200 Texas Street, Fort Worth, Texas 76102, with copies to the Fort Worth City Attorney at the same address. (d) The insurers for all policies must be licensed and/or approved to do business in the State of Texas. All insurers must have a minimum rating of A- VII in the current A.M. Best Key Rating Guide, or have reasonably equivalent financial strength and solvency to the satisfaction of Risk Management. If the rating is below that required, written approval of Risk Management is required. (e) Any failure on the part of City to request required insurance documentation will not constitute a waiver of the insurance requirement. (f) Certificates of Insurance evidencing that Vendor has obtained all required insurance will be delivered to the City prior to Vendor proceeding with any work pursuant to this Agreement. 11. Compliance with Laws, Ordinances, Rules and Regulations. Vendor agrees that in the performance of its obligations hereunder, it will comply with all applicable federal, state and local laws, ordinances, rules and regulations and that any work it produces in connection with this Agreement will also comply with all applicable federal, state and local laws, ordinances, rules and regulations. If City notifies Vendor Services Agreement Page 5 of 12 City Secretary Contract No. Vendor of any violation of such laws, ordinances, rules or regulations, Vendor must immediately desist from and correct the violation. 12. Non -Discrimination Covenant. Vendor, for itself, its personal representatives, assigns, contractors, subcontractors, and successors in interest, as part of the consideration herein, agrees that in the performance of Vendor's duties and obligations hereunder, it will not discriminate in the treatment or employment of any individual or group of individuals on any basis prohibited by law. IF ANY CLAIM ARISES FROM AN ALLEGED VIOLATION OF THIS NON-DISCRIMINATION COVENANT BY VENDOR, ITS PERSONAL REPRESENTATIVES, ASSIGNS, CONTRACTORS, SUBCONTRACTORS, OR SUCCESSORS IN INTEREST, VENDOR AGREES TO ASSUME SUCH LIABILITY AND TO INDEMNIFY AND DEFEND CITY AND HOLD CITY HARMLESS FROM SUCH CLAIM. 13. Notices. Notices required pursuant to the provisions of this Agreement will be conclusively determined to have been delivered when (1) hand -delivered to the other party, its agents, employees, servants or representatives, (2) delivered by facsimile with electronic confirmation of the transmission, or (3) received by the other party by United States Mail, registered, return receipt requested, addressed as follows: To CITY: City of Fort Worth Attn: Assistant City Manager 200 Texas Street Fort Worth, TX 76102-6314 Facsimile: (817) 392-8654 With copy to Fort Worth City Attorney's Office at same address To VENDOR: Zone Industries LLC, Collin Brown, Branch Manager 1970 Business Park BLVD Argyle, TX 76226 Facsimile: 14. Solicitation of Emplovees. Neither City nor Vendor will, during the term of this Agreement and additionally for a period of one year after its termination, solicit for employment or employ, whether as employee or independent contractor, any person who is or has been employed by the other during the term of this Agreement, without the prior written consent of the person's employer. Notwithstanding the foregoing, this provision will not apply to an employee of either party who responds to a general solicitation of advertisement of employment by either party. 15. Governmental Powers. It is understood and agreed that by execution of this Agreement, City does not waive or surrender any of its governmental powers or immunities. 16. No Waiver. The failure of City or Vendor to insist upon the performance of any term or provision of this Agreement or to exercise any right granted herein does not constitute a waiver of City's or Vendor's respective right to insist upon appropriate performance or to assert any such right on any future occasion. 17. Governing Law / Venue. This Agreement will be construed in accordance with the laws of the State of Texas. If any action, whether real or asserted, at law or in equity, is brought pursuant to this Agreement, venue for such action will lie in state courts located in Tarrant County, Texas or the United States District Court for the Northern District of Texas, Fort Worth Division. Vendor Services Agreement Page 6 of 12 City Secretary Contract No. 18. Severability. If any provision of this Agreement is held to be invalid, illegal or unenforceable, the validity, legality and enforceability of the remaining provisions will not in any way be affected or impaired. 19. Force Maieure. City and Vendor will exercise their best efforts to meet their respective duties and obligations as set forth in this Agreement, but will not be held liable for any delay or omission in performance due to force majeure or other causes beyond their reasonable control, including, but not limited to, compliance with any government law, ordinance, or regulation; acts of God; acts of the public enemy; fires; strikes; lockouts; natural disasters; wars; riots; epidemics or pandemics; government action or inaction; orders of government; material or labor restrictions by any governmental authority; transportation problems; restraints or prohibitions by any court, board, department, commission, or agency of the United States or of any States; civil disturbances; other national or regional emergencies; or any other similar cause not enumerated herein but which is beyond the reasonable control of the Party whose performance is affected (collectively, "Force Majeure Event"). The performance of any such obligation is suspended during the period of, and only to the extent of, such prevention or hindrance, provided the affected Party provides notice of the Force Majeure Event, and an explanation as to how it prevents or hinders the Parry's performance, as soon as reasonably possible after the occurrence of the Force Majeure Event, with the reasonableness of such notice to be determined by the City in its sole discretion. The notice required by this section must be addressed and delivered in accordance with Section 13 of this Agreement. 20. Headings not Controlling. Headings and titles used in this Agreement are for reference purposes only, will not be deemed a part of this Agreement, and are not intended to define or limit the scope of any provision of this Agreement. 21. Review of Counsel. The parties acknowledge that each party and its counsel have reviewed and revised this Agreement and that the normal rules of construction to the effect that any ambiguities are to be resolved against the drafting party will not be employed in the interpretation of this Agreement or Exhibits A, B, and C. 22. Amendments / Modifications / Extensions. No amendment, modification, or extension of this Agreement will be binding upon a party hereto unless set forth in a written instrument, which is executed by an authorized representative of each party. 23. Counterparts. This Agreement may be executed in one or more counterparts and each counterpart will, for all purposes, be deemed an original, but all such counterparts will together constitute one and the same instrument. 24. Warranty of Services. Vendor warrants that its services will be of a high quality and conform to generally prevailing industry standards. City must give written notice of any breach of this warranty within thirty (30) days from the date that the services are completed. In such event, at Vendor's option, Vendor will either (a) use commercially reasonable efforts to re -perform the services in a manner that conforms with the warranty, or (b) refund the fees paid by City to Vendor for the nonconforming services. 25. Immigration Nationalitv Act. Vendor must verify the identity and employment eligibility of its employees who perform work under this Agreement, including completing the Employment Eligibility Verification Form (I-9). Upon request by City, Vendor will provide City with copies of all I-9 forms and supporting eligibility documentation for each employee who performs work under this Agreement. Vendor must adhere to all Federal and State laws as well as establish appropriate procedures Vendor Services Agreement Page 7 of 12 City Secretary Contract No. and controls so that no services will be performed by any Vendor employee who is not legally eligible to perform such services. VENDOR WILL INDEMNIFY CITY AND HOLD CITY HARMLESS FROM ANY PENALTIES, LIABILITIES, OR LOSSES DUE TO VIOLATIONS OF THIS PARAGRAPH BY VENDOR, VENDOR'S EMPLOYEES, CONTRACTORS, SUBCONTRACTORS, OR AGENTS. City, upon written notice to Vendor, will have the right to immediately terminate this Agreement for violations of this provision by Vendor. 26. Ownership of Work Product. City will be the sole and exclusive owner of all reports, work papers, procedures, guides, and documentation that are created, published, displayed, or produced in conjunction with the services provided under this Agreement (collectively, "Work Product"). Further, City will be the sole and exclusive owner of all copyright, patent, trademark, trade secret and other proprietary rights in and to the Work Product. Ownership of the Work Product will inure to the benefit of City from the date of conception, creation or fixation of the Work Product in a tangible medium of expression (whichever occurs first). Each copyrightable aspect of the Work Product will be considered a "work -made - for -hire" within the meaning of the Copyright Act of 1976, as amended. If and to the extent such Work Product, or any part thereof, is not considered a "work -made -for -hire" within the meaning of the Copyright Act of 1976, as amended, Vendor hereby expressly assigns to City all exclusive right, title and interest in and to the Work Product, and all copies thereof, and in and to the copyright, patent, trademark, trade secret, and all other proprietary rights therein, that City may have or obtain, without further consideration, free from any claim, lien for balance due, or rights of retention thereto on the part of City. 27. Signature Authoritv. The person signing this Agreement hereby warrants that they have the legal authority to execute this Agreement on behalf of the respective party, and that such binding authority has been granted by proper order, resolution, ordinance or other authorization of the entity. This Agreement and any amendment hereto, may be executed by any authorized representative of Vendor. Each party is fully entitled to rely on these warranties and representations in entering into this Agreement or any amendment hereto. 28. Change in Companv Name or Ownership. Vendor must notify City's Purchasing Manager, in writing, of a company name, ownership, or address change for the purpose of maintaining updated City records. The president of Vendor or authorized official must sign the letter. A letter indicating changes in a company name or ownership must be accompanied with supporting legal documentation such as an updated W-9, documents filed with the state indicating such change, copy of the board of director's resolution approving the action, or an executed merger or acquisition agreement. Failure to provide the specified documentation so may adversely impact future invoice payments. 29. No Bovcott of Israel. If Vendor has fewer than 10 employees or this Agreement is for less than $100,000, this section does not apply. Vendor acknowledges that in accordance with Chapter 2271 of the Texas Government Code, the City is prohibited from entering into a contract with a company for goods or services unless the contract contains a written verification from the company that it: (1) does not boycott Israel; and (2) will not boycott Israel during the term of the contract. The terms "boycott Israel" and "company" has the meanings ascribed to those terms in Section 2271 of the Texas Government Code. By signing this Agreement, Vendor certifies that Vendor's signature provides written verification to the City that Vendor: (1) does not boycott Israel; and (2) will not boycott Israel during the term of the Agreement. 30. Prohibition on Bovcotting Enerav Companies. Vendor acknowledges that in accordance with Chapter 2274 of the Texas Government Code (as added by Acts 2021, 87th Leg., R.S., S.B. 13, § 2), the City is prohibited from entering into a contract for goods or services that has a value of $100,000 or more, which will be paid wholly or partly from public funds of the City, with a company (with 10 or more Vendor Services Agreement Page 8 of 12 City Secretary Contract No. full-time employees) unless the contract contains a written verification from the company that it: (1) does not boycott energy companies; and (2) will not boycott energy companies during the term of the contract. The terms "boycott energy company" and "company" have the meaning ascribed to those terms by Chapter 2274 of the Texas Government Code (as added by Acts 2021, 87th Leg., R.S., S.B. 13, § 2). To the extent that Chapter 2274 of the Government Code is applicable to this Agreement, by signing this Agreement, Vendor certifies that Vendor's signature provides written verification to the City that Vendor: (1) does not boycott energy companies; and (2) will not boycott energy companies during the term of this Agreement. 31. Prohibition on Discrimination Against Firearm and Ammunition Industries. Vendor acknowledges that except as otherwise provided by Chapter 2274 of the Texas Government Code (as added by Acts 2021, 87th Leg., R.S., S.B. 19, § 1), the City is prohibited from entering into a contract for goods or services that has a value of $100,000 or more which will be paid wholly or partly from public funds of the City, with a company (with 10 or more full-time employees) unless the contract contains a written verification from the company that it: (1) does not have a practice, policy, guidance, or directive that discriminates against a firearm entity or firearm trade association; and (2) will not discriminate during the term of the contract against a firearm entity or firearm trade association. The terms "discriminate," "firearm entity" and "firearm trade association" have the meaning ascribed to those terms by Chapter 2274 of the Texas Government Code (as added by Acts 2021, 87th Leg., R.S., S.B. 19, § 1). To the extent that Chapter 2274 of the Government Code is applicable to this Agreement, by signing this Agreement, Vendor certifies that Vendor's signature provides written verification to the City that Vendor: (1) does not have a practice, policy, guidance, or directive that discriminates against a firearm entity or firearm trade association; and (2) will not discriminate against a firearm entity or firearm trade association during the term of this Agreement. 32. Electronic Signatures. This Agreement may be executed by electronic signature, which will be considered as an original signature for all purposes and have the same force and effect as an original signature. For these purposes, "electronic signature" means electronically scanned and transmitted versions (e.g. via pdf file or facsimile transmission) of an original signature, or signatures electronically inserted via software such as Adobe Sign. 33. Entirety of Agreement. This Agreement contains the entire understanding and agreement between City and Vendor, their assigns and successors in interest, as to the matters contained herein. Any prior or contemporaneous oral or written agreement is hereby declared null and void to the extent in conflict with any provision of this Agreement. (signature page follows) Vendor Services Agreement Page 9 of 12 City Secretary Contract No. I:T90101WI101I7:1121P7:T14SDID103 CITY OF FORT WORTH: Pang &r hdoff By: Dana Burghdoff (Jan 8, 02417:53 CST) Name: DanaBurghdoff Title: Assistant City Manager Date: Jan 8, 2024 APPROVAL RECOMMENDED: GLcri� HArr7er By: Christopher Hanher(Jan 5, 202406:32 CST) Name: Christopher Harder) Title: Water Director ATTEST: By: Name: Jannette Goodall Title: City Secretary VENDOR: Zone Industries By: CAiUM GLa1Af n Name: _Collin Brown Title: Date: November 20th 2023 CONTRACT COMPLIANCE MANAGER: By signing I acknowledge that I am the person responsible for the monitoring and administration of this contract, including ensuring all performance and reporting requirements. By: Name: Mark Wilson Title: Sr. Professional Engineer APPROVED AS TO FORM AND LEGALITY: By: DBIack(Jan 4, 202417:33 CST) Name: DougBlack Title: Sr.Assistant City Attorney CONTRACT AUTHORIZATION: M&C: N/A Form 1295: OFFICIAL RECORD CITY SECRETARY FT. WORTH, TX Vendor Services Agreement Page 10 of 12 Exhibit A CITY OF FORT WORTH PACKAGE PUMPING SYSTEM FOR HARMON ROAD TANK FACILITY SCOPE OF WORK 1. Design, construct, and deliver to the project site a packaged pumping system with (2) skid - mounted centrifugal potable water pumps. The intended use of the packaged pumping system is to transfer potable water from one pressure plane to a higher -pressure plane at the location of the existing Harmon Road elevated storage tank. The pumps should be able to be fully operated remotely via the City's SCADA system. City staff would engage the pumping system when the Harmon Road tank (located in the higher -pressure plane) is low. Major components of the pumping system are as follows: a. Suction and discharge headers b. Pump controllers c. Electronics panel to allow City staff to connect a PLC controller for the means of controlling the pumping system remotely d. Pump isolation and control valves e. Air release valves f. Instrumentation including suction and discharge pressure transmitters g. Manual pressure gauges for suction and discharge h. Steel support base structure 2. City Purchase Order shall be issued no later than December 1, 2023 3. Pumping system shall be delivered to the following address no later than June 1, 2024: a. 1645 Harmon Rd. Fort Worth, Texas 4. Available electrical capacity at the site: a. 480 Volts b. 3 Phase c. 200 Amps (available to package pumping system) MEASUREMENT AND PAYMENT 1. Packaged Pumping System: No unit measurements will be made for the Packaged Pumping System. Payment will be made at the schedule below. Includes pumps, motors, piping, valves, base platform, and all appurtenances required to complete a full operational system. Piping between existing facilities and suction and discharge headers, as well as SCADA connections will be installed by City. a. 10% at shop drawing approval b. 80% at delivery of pumping system to the project site c. 10% upon successful testing and commissioning of the pumping unit d. Should the equipment not be delivered to the site within the time specified by the Vendor in their proposal, liquidated damages shall be assessed at the rate of $500 per day, up to a maximum of 10% of the total proposal price. Packaged Pumping System City of Fort Worth 1 SUBMITTALS 1. Submit to the City copies of all materials required to establish compliance with this section. Submittals shall include at least the following: a. Before the City issues a Purchase Order for the pumping system, Selected Vendor shall submit a detailed schedule showing critical path items and delivery date. Vendor shall submit a monthly update showing progress of the project toward completion. b. Certified shop and erection drawings showing all important details of construction, dimensions and anchor bolt locations. c. Descriptive literature, bulletins and catalogs of the equipment. d. Control panel layout drawings showing dimensions, finishes, interior and exterior views, bill of materials wire and terminal numbers. Provide schematic wiring diagrams showing interconnections with external devices. e. The total weight of equipment package and the weight of each major component. f. A complete total bill of materials. g. A complete description of surface preparation and shop prime painting. h. Submittals must be specific to this project. Generic submittals will not be accepted. Components listed in this specification are subject to change based on availability. A like component may be substituted and submitted for approval. i. Shop drawing submittals will be reviewed and returned to the Vendor within 5 business days of receipt in order to mitigate production schedule impacts. 2. Test Reports a. Witness testing of pump test is not required. b. A certified copy of factory tests of hydrostatic pressure and performance for pumps shall be provided to the City. c. A copy of hydrostatic test of completed packaged pump system shall be provided to the City. 3. Operations and Maintenance a. Submit operating and maintenance instructions to the City. The instructions shall be prepared specifically for this installation and shall include all required cuts, drawings, equipment lists, description, etc., that are required to instruct operating personnel unfamiliar with such equipment. b. Vendor shall submit a site acceptance test report to City and also include it in the Operations and Maintenance manual. REFERENCE STANDARDS 1. AWWA — American Water Works Association 2. ANSI —American National Standards Institute 3. ASTM — American Society for Testing and Materials 4. HI — Hydraulic Institute 5. ASME —American Society of Mechanical Engineers 6. IEEE — Institute of Electrical and Electronics Engineers 7. NEMA— National Electrical Manufacturers Association 8. NEC — National Electrical Code 9. ISO — International Standards Organization Packaged Pumping System City of Fort Worth 2 10. UL— Underwriters Laboratories, Inc. 11. IEC — International Electrotechnical Commission 12. NSF — National Sanitation Foundation QUALITY ASSURANCE 1. The pumping package shall be manufactured and assembled by the pump manufacturer or a factory authorized reseller. An assembler of pumping systems not actively engaged in the design and construction of centrifugal pumps or pumping systems shall not be considered a pump manufacturer. The manufacturer shall assume "Unit Responsibility" for the complete pumping package. Unit responsibility shall be defined as responsibility for interface and successful operation of all project system components supplied by the pumping system manufacturer. 2. The manufacturer shall have a minimum of 10 years' experience in the design and construction of packaged pumping systems. Provide three references with Proposal. 3. Vendors shall comply with all sections of this specification relating to packaged pumping systems. Any deviations from this specification shall be listed as an Exemption in the Proposal Quote section of this document as a voluntary alternate clearly defined in writing. If no exceptions are noted, the supplier or contractor shall be bound by these specifications. SYSTEM DESCRIPTION 1. City staff shall connect the Package Pumping System to existing stainless -steel piping at the site. 2. City SCADA system shall be used to control each pump remotely. When suction pressure is sufficient, staff shall engage one or both pumps to provide additional volume into the storage tank. 3. Pump isolation valves and check valves shall prevent backflow through each pump. 4. Air release valves shall remove entrained air from the system in order to keep pressurized piping full of water and reduce excess dissolved water in the City's potable water system. 5. Pump system control panel shall allow local operation and troubleshooting. DELIVERY, STORAGE, AND HANDLING 1. All parts of the pumping system shall be properly protected during assembly and while shipping to the project site to prevent damage. 2. Finished iron or steel surfaces not painted shall be properly protected to prevent rust and corrosion; maintain protection until operation. 3. After hydrostatic or other tests, all entrapped water shall be drained prior to shipment and proper care shall be taken to protect parts from the entrance of water during shipment, storage and handling. PRODUCTS 1. Centrifugal Pumps a. Design (assuming two pumps at approximately 100 HP) i. Duty Point: 4,175 gpm @ 72 feet TDH (per pump) ii. Requirement: 100 feet TDH shall fall within Allowable Operating Range b. Net Positive Suction Head (NPSH) i. Suction is flooded Packaged Pumping System City of Fort Worth 3 ii. Available NPSH: 32 feet iii. Required NPSH: Pump NPSHr shall not be greater than Hydraulic Institute recommendations. Minimum margin shall be 10 percent within preferred operating range, or 5 feet, whichever is greater. c. Approved Manufacturers i. Flowserve ii. Cornell iii. Goulds iv. Xylem v. Or approved equal d. Construction i. Pumps and motors shall be close -coupled ii. Pumps and motors may be vertical or horizontal orientation as long as the pumping package can be moved through the existing 10 feet by 10 feet overhead door. iii. Impellers shall be of bronze or 316 Stainless Steel iv. Impellers shall be of strong dense castings free of structural defects with uniform thickness of vanes and shrouds. They shall be the enclosed type with staggered vane design, have smooth water passages for high efficiency, and shall be statically and dynamically balanced. v. Pump casing shall be of strong close -grain cast iron in accordance with ASTM A48 Class 30, or ductile iron in accordance with ASTM A536 designed for heavy duty service. vi. Horizontal pump casings shall be drilled and tapped for air release valve, and drain connections. Suitable lifting lugs or eye bolts shall be provided. Casing shall be tested in accordance with Hydraulic Institute Standard 14.6 under a hydrostatic pressure of 150% of maximum shut-off head. vii. Pump shaft shall be of ample conservative design such that it will be suitable to transmit the maximum brake horsepower required by the pump, and be of sufficient stiffness to prevent contact of the wearing rings under any condition of operation. 2. Pump Motors a. Motors shall be rated at 480 Volt, 3 phase, 60 hertz b. Motors shall be air cooled, solid shaft, copper wound stator, copper bar rotor construction, squirrel cage induction type. The motors shall be designed for starting using across the line starter and variable frequency drive. c. Horsepower nameplate rating of motor, at the 1.0 service factor, shall be equal to or greater than the total horsepower requirement of the pump when operating at any head between shut-off and minimum specified operating heads. Motor shall have a service factor of 1.15 and shall be designed and manufactured in accordance with applicable provisions of the latest NEMA Standard Publication for Motors and Generators, MG-1 Part 20, subject to modifications and additions as herein set forth. d. Motors shall be rated for inverter duty per NEMA MG-1, Part 31. Packaged Pumping System City of Fort Worth 4 e. The locked rotor torque and breakdown torque shall not be less than shown in NEMA 20.10. f. The locked rotor KVA/HP shall not exceed NEMA code Letter F, 5.59 KVA/HP. g. Rotor shall be "precision" balanced to within an amplitude peak to peak in accordance with the requirement of NEMA MG-1. h. Rotor bars and end rings shall be copper or copper alloy (no substitution). The rotor bars shall be swaged. The end rings shall be joined to the rotor bars by high frequency induction brazing. The rotor cores shall be held together by through -bolts and end plates. i. The stator shall have all connections brazed with silver brazing alloy. The stator shall be braced and supported to eliminate any detrimental winding movement. j. The stator core shall be built up with high grade, non -aging laminated silicon steel, C5 or better in accordance with ASTM A 345. Each lamination core shall be plated to minimize eddy current losses. The laminations shall be adequately secured to the stator frame and securely held in place at each end. There shall be no perceptible buzzing of laminations during operation. Provide slot wedges for rigidity. k. Motor efficiency shall not be less than 95% and power factor not less than 85% uncorrected when operating at full load and rated voltage and frequency. I. Motors shall be capable of bringing the pumps up to speed with a closed control valve and 80% of rated voltage. m. Motor bearings shall be designed for the maximum load imposed by the pump and motor and shall be selected for a 5-year minimum life and 25-year average life. Bearings shall be ring oiled, split -sleeve type. Bearings shall be insulated to prevent shaft -bearing - frame current. Insulating means shall also be provided for any oil -supply connections and monitoring equipment to prevent electrical bypassing of the bearing insulation. n. All wires and electrical connections shall be copper. All wiring penetrating motor frame shall be protected against chaffing with a rubber grommet. 3. Pump Control Panel a. Operation of pump control panel shall allow for both local and remote starting with capability of low suction pressure interlocks/permissives. b. Required 1/0 (dry contacts) to allow City staff to connect HSQ compatible PLC controller system i. Pump start ii. Pump stop iii. Run status iv. Suction pressure v. Discharge pressure vi. Common alarm c. All power and controls components including the controller, and other electrical components shall be housed and mounted in UL Type 12 rated enclosures. A self - certified NEMA enclosure rating shall not be considered equal. The entire control panel shall be UL 508 listed as an assembly and warranted by the pump station manufacturer. All equipment and wiring shall be mounted within the enclosure and each device shall be labeled for proper identification. A complete wiring circuit diagram and legend with Packaged Pumping System City of Fort Worth 5 terminals, components, and wiring completely identified shall be provided. The control panel shall include a main disconnect, branch circuit and overload protection for each pump -motor and the control circuit and control relays for alarm functions. d. Control panel shall include as standard: i. Main Disconnect Switch ii. Fault/Alarm Indicator Light iii. Pump Run Light iv. Hand/Off/Auto switch for each pump v. Local Start button for each pump vi. Local Stop button for each pump e. Panel Manufacturer shall be competent and experienced panel builders. All panels shall be UL listed and certified and shall have the proper UL listing plaques or stickers in a prominent area of the panel for easy verification of UL listing. f. Manufacturer shall be authorized by Underwriters' Laboratories to label its manufactured control panels as UL Listed under category NITW /NITW7. g. Manufacturer shall conform to the latest edition of NFPA 70 in the manufacturing of its control panels. h. The control enclosures shall be constructed of 12 gauge painted steel and the back plate assembly shall be constructed of 12 gauge painted steel. i. Pump run lights, pump selector switches, the general alarm light, the reset button, and the touch screen shall be mounted on an enclosure door. All of these components shall be rated NEMA 4. j. All internal components shall be mounted and secured to the removable back plate assembly. All equipment and wiring shall be mounted within the enclosure and labeled for proper identification. k. All adjustments and maintenance shall be able to be done from the front of the control enclosure. I. A complete wiring circuit and legend with all terminals, components, and wiring identification shall be provided. 4. Electrical Conduits a. Rigid aluminum conduit, couplings, factory elbows, and fittings shall be 6063 alloy by Allied Tube & Conduit Co., or approved equal. Conduit hubs shall be insulated throat by Crouse -Hinds. b. Minimum conduit size shall be W c. Top conduit entry into accessories terminal boxes is not acceptable. 5. Electrical Cables a. Motor circuit wiring shall be sized for load. All branch circuit conductors which supply a single motor shall have an ampacity of not less than 125 percent of the motor full load current based upon NEC table 430.250 b. Wiring shall be dual rated type THHN/THWN, as set forth in Article 310 and 430 Part II of the National Electrical Code. c. Control and accessory wiring shall be sized for load, type MTW/AWM (Machine Tool Wire/Appliance Wiring Material) as set forth in Article 310 and 670 of the National Packaged Pumping System City of Fort Worth 6 Electrical Code, except where accessories are furnished with a manufacturer supplied UL approved rubber cord and plug. 6. Potable Water Piping a. All water piping shall conform to the following standards: i. NSF 61 certified ii. AWWA C200 b. All water piping 2 inches and larger in diameter shall be carbon steel with the following features and standards: i. Internally and externally coated with NSF 61 approved epoxy paint. Epoxy paint shall conform to AWWA C210. c. All piping less than 2 inches in diameter shall be 304 stainless steel d. Velocity shall not exceed 15 feet per second in any piping e. Suction Header i. Size:24" ii. Each end shall be flanged with one end having a blind flange. f. Discharge Header i. Size:16" ii. Each end shall be flanged with one end having a blind flange. g. Flanged carbon steel fittings shall be Class 150 as appropriate for system working pressure. h. Grooved piping fittings are allowed on all component connections except for at the pump and isolation valves. Grooved piping fittings shall be cast iron, ductile iron, or carbon steel construction. Grooved fittings shall have a maximum allowable working pressure of 300 psi or greater. i. Welders performing structural and pipe welds shall be certified to ASME section IX, and their certificates shall be on file with the manufacturer. Upon request by the engineer or City, the certificates shall be made available for inspection. 7. Instrumentation a. Suction and Discharge Pressure Transmitters i. Rosemount model 3051 ii. 4-20 mA output signal 8. Manual Taps and Gauges a. Suction and Discharge Pressure Gauges i. Provide a manual suction and manual discharge pressure gauge on each header. ii. Gauges shall be 4 inch 316 stainless steel with full body stainless monolithic block and bleed valves. iii. Gauge stem shall be 3/8" diameter iv. Gauges shall have a ball valve prior to the gauge to allow replacement of the gauge as necessary. 9. Valves a. Isolation Valves i. Isolation valves shall be provided upstream and downstream of each pump so that a pump train can be taken out of service without affecting the other pump train. Packaged Pumping System City of Fort Worth 7 ii. Isolation valves shall be gate or butterfly style. iii. Gate valves shall conform to AWWA C509 or C515 standard iv. Butterfly valves shall conform to AWWA C504 standard v. Pump isolation valves shall be flanged valves b. Pump Discharge Valves i. Pump discharge piping shall have a one-way valve (check valve) for preventing backflow through the pump. Acceptable valve types are: 1. Wafer 2. Tilted disc 3. Swing c. Air release valves i. Air release valves shall conform to AWWA C512 standard ii. Each pump shall have an air release valve in the high point of the discharge piping. d. Header Drains i. Provide a ball valve at the lowest point of each header to drain the header. 10. Reducers a. Reducers shall conform to AWWA C153 standard b. Reducers shall be eccentric with straight section at the highest point so as to not trap air. 11. Steel Support Base Structure a. Steel i. Base structure shall be constructed of fabricated carbon steel. ii. All materials used in the construction of the base shall be new materials. iii. All structural steel shapes, bars, and plates shall be ASTM A36 grade meeting the requirements of ASTM A6. b. Design i. Load bearing beams shall be contained within and welded to a steel, I-beam or structural channel exterior. ii. Appropriate space and clearance shall be provided for access, operation, and maintenance of supplied equipment. iii. Base unit shall be constructed as open I-beam or C-channel base that shall be sized for the weight of the equipment being provided. Open frame design shall be capable of being filled with concrete or other sound and vibration damping material once installed on -site by City. All equipment shall be attached to the main base members and connected appropriately (including pump, driver, and controller). iv. Lifting provisions shall be incorporated into the pump base design. The preferred method of lifting provision shall be lifting lugs installed in the exterior running members of the base structure. The base structure will also need to be strong enough to be moved laterally into place by fork lift and dolly or portable crane structure. v. Base unit shall be narrow enough to fit through a 10 feet wide overhead door with a clear opening of 116 inches. Height of the door is 10 feet high. Packaged Pumping System City of Fort Worth 8 vi. Base unit shall have a means of securely attaching to a concrete slab. c. Manufacture i. All welded structural members, brackets, pipe supports, equipment supports, and racks will be completely seal welded. Plates may be stitch welded. ii. All structural welds shall be performed by AWS D1.1 certified welders. iii. All welds shall be of high quality and ground clean. The welds shall be free of slag, pinholes, and undercut. iv. All major equipment shall be bolded to the main base structural members. Equipment may be installed on stands, risers, etc. No equipment may be attached to floor plate or light weight (less than W) angle brackets. v. Base structure shall be provided with two drilled and tapped grounding lugs located at opposite corners of the base and seal welded to the exterior structural member web. d. Coatings i. All pre -fabricated items including but not limited to, platform for pumplq mounting, panel mounting frame, and all piping shall be sandblasted per SSPC- SP10 to a near white metal condition. The cleaned steel surfaces shall immediately thereafter be primed with an industrial grade epoxy primer to a thickness of 2.5 to 3 mils. Paint shall be light blue color. All nuts, bolts, and miscellaneous assembly hardware used for component -to -component assembly shall be stainless steel to prevent corrosion. TESTING 1. The piping system shall undergo a factory hydrostatic test at the end of the production cycle. The piping system shall be filled with water and pressurized to 1.5 times the pump nameplate design pressure or 1.25 times pump shutoff pressure whichever is greater. The pressure shall be maintained for a minimum of 10 minutes with no leakage prior to shipment. Full system hydro - test can be offered if requested. 2. Packaged pumping system shall be installed by City staff with technical support from Vendor. Once package is installed at site, another hydrotest shall be required to ensure all bolts and fittings are tightly secured prior to startup (per installation instructions). 3. Field Testing and Startup: a. Vendor or pump factory representative shall perform a pumping system acceptance test at the site to determine if all package components are working correctly. Vendor shall submit the final report to the City. b. Vendor shall verify 3 points on the pump curve for each pump by varying closure on the discharge isolation valve. Data sheet information for each test shall be at least: i. Flow Rate ii. Suction Pressure iii. Discharge Pressure iv. Calculated TDH v. Discharge Isolation Valve % closed vi. Amps Packaged Pumping System City of Fort Worth 9 WARRANTY 1. The manufacturer shall warrant the water pumping system to be free of defects in material and workmanship for two years (24 months) from date of authorized start-up. INSURANCE The Vendor shall assume all risk and liability for accidents and damages that may occur to person or property during the prosecution of work under this agreement. The Vendor shall file with the City of Fort Worth Purchasing Division, prior to the commencement of services, a certificate of insurance documenting the following insurance requirements: 1. Commercial General Liability: a. $1,000,000 each occurrence b. $2,000,000 aggregate limit 2. Automobile Liability: a. $1,000,000 each accident on combined basis b. $250,000 bodily injury per person c. $500,000 bodily injury per accident d. $100,000 property damage 3. Workers Compensation and Employers Liability: a. $100,000 each accident b. $100,000 disease —each employee c. $500,000 disease - policy 4. Additionally Insured: a. Policy to list City of Fort Worth as Additionally Insured Packaged Pumping System City of Fort Worth 10 Exhibit B PROPOSAL QUESTIONS 1. Questions regarding the specification shall be directed to Mark Wilson, (817) 392-8408, Mark.Wilson2@FortWorthTexas.gov PROPOSAL QUOTE To be considered a responsive submitter, the following items must be completed: 1. Shop drawings and material selections shall be delivered to City 3-4 weeks after award of contract and receipt of Purchase Order. 2. Packaged Pumping System shall be delivered to project site 18 weeks after City approval of Shop Drawings and material selections. 3. Total cost to supply Packaged Pumping System as specified in this document shall be $ 249,982.00 4. Required attachments to quote submittal: Y Pump Manufacturer's Pump Curve Y General Layout of Packaged Pump System with overall dimensions showing Length, Width, and Height Y Warranty Language Y Reference Sheet (3 references) 5. Any proposed manufacturers or component type or construction type that would deviate from the above specification shall be listed below. Exceptions will not necessarily disqualify the proposal, especially if the exception or substitution is needed to meet the required delivery date and does not degrade the overall function or lifespan of the pumping system. ❑ Exception 1: Motors quoted are manufacturer's standard construction, premium efficient, inverter duty. u Exception 2: ❑ Exception 3: ❑ Exception 4: 6. Acknowledgement of Addendums: Y Addendum 1 Y Addendum 2 ❑ Addendum 3 ❑ Addendum 4 Date: November 16, 2023 Company Name: Zone Industries Signature: Name and Title: Randy Key/ Application Engineer Contact Information: 817-912-5151 rkey@zoneindustries.com Packaged Pumping System City of Fort Worth 11 Ir2ZONE INDUS7RIES 1) Job Name: Brazoria MUD 21 Zone Industries 820 W Sandy Lake Rd Suite 200 Coppell, TX 75019 P:817-912-5151 F:713-783-1221 Reference List PPS Packaged Pump Stations a. Date: October 2023 b. Location: Pearland, TX c. Type of system: Wastewater Effluent, suction lift d. Two 5hp motors 2) Job Name: Bridgelands IPS 7 a. Date: April 2021 b. Location: Houston, TX c. Type of system: Vertical Turbine d. Motors: Three 100hp and one 5hp 3)Job Name: Liberty Golf Course a. Date: June 2021 b. Location: Liberty, TX c. Type of system: Vertical Turbines d. Motors: Two 40hp and one 5hp ZONE INDUSTRIES PROJECT: HARMON ROAD BOOSTER MODEL NUMBER: CB##C2C100X04175-031XXXX4831AS-24 Design Point: Design Flow Rate - GPM: Intake Pressure - PSI: Station Pressure - PSI: Discharge Pressure - PSI: FUNCTION QTY MAIN/DUTY 2 1 4175 31.16 31.16 HP PUMP PERFORMANCE 100 4175 GPM @ 72' TDH SPECIAL MOTOR DESIGN/ADDITIONS Premium Efficiency Motors (Default for all standard motors provided) Inverter Duty Rated Motors included LOCATION CITY: FORT WORTH STATE: TX - TEXAS Voltage: 480 Electrical Loads AMPS Phase: 3 DISCONNECT 400 Hertz: 60 NEC FLA 281 LEAD/STANDBY RPM TYPE/BRAND MOTOR ENCLOSURE 1800 END -SUCTION CENTRIFUGAL ODP CORNELL M SYSTEM TYPE: FLOODED SUCTION INTAKE SOURCE: POTABLE DISCHARGE USE: POTABLE - NSF RATED - HUMAN CONSUMPTION PUMP STATION ENCLOSURE: CUSTOMER SUPPLIED BUILDING PRESSURE TRANSMITTERS (2) ROSEMOUNT MODEL 3051 INCLUDED #REF! 0 SKID BASE SIZE (INCHES): 96X144 Estimated - Do not use for construction. Contact PPS for detailed drawing/info. • UL QCZJ Certified pumping system • This quote/estimate is for a factory tested system and/or components. • The pump station shall include all pumps described above, as well as all necessary valves and piping (See details below). • If provided the variable frequency control panel for the pump station will be prewired and pretested. • If provided the system will be controlled by a PLC and HMI Touchscreen with programming written specific to the project. • Control Panel is NEMA 12 manufactured for INDOOR operation. DESIGN CRITERIA (Quotation is based on the following specifications/information): • Customer supplied design point information. • Information noted in the above Design Details & Pump Selections. Deviation from details specified above may impact pricing • PPS is not responsible for any errors or omissions due to incomplete or inaccurate information. CERTIFIED START-UP, CALIBRATION, TRAINING INCLUDES 1 PPS TECHNICIAN FOR A MAXIMUM OF 6 HOURS ON SITE FOR START-UP AND CALIBRATION OF PUMP STATION & OPERATOR TRAINING - MUST BE SCHEDULED A MINIMUM OF 2 WEEKS IN ADVANCE - ANY ADDITIONAL TIME REQUIRED WILL BE CHARGED TO CUSTOMER Precision Pumping Systems (PPS) warrants that its products and systems will be free from defects in material and workmanship for a period of twenty four (241 months from the date of placing the equipment in operation. When notified by Purchaser of a defect which conforms to this Warranty PPS shall, at its sole discretion, correct the defect by performing a suitable repair to the Equipment or by providing a replacement part. This warranty does not apply to equipment that has been damaged, misapplied or modified in any way. SHIPMENT/DEVVERY. All reasonable efforts will be made to meet the requested shipment date after the receipt of a signed purchase order and approval of submittal(s). Manufacturer will not be held liable for delays in shipment or delivery. • Appropriate power to be provided by others - voltage & phase specified above from Customer provided information • Offloading & set up by others • Wet well, concrete pad(s), intake structure or other civil works to be provided by others. • Tie-in to main line and flush lines to be performed by others • Start-up and calibration by a PPS certified technician. • No taxes are included in this quotation. • ENVIRONMENTAL DESIGN: NEMA 12 cabinet manufactured for INDOOR operation • MOTOR STARTING PRIMARY: SOFT STARTER ONLY • VFD MODEL: BEST FIT FOR APPLICATION • PANEL COOLING: FORCED AIR • CONTROL SYSTEM MODEL NUMBER: MMC2X100PSTX-483-LA-ICM-U3F-PLC6E-HG7C-UPS-VZW-AWWA-CUSTOM • CONTROL PANEL MODEL NUMBER: HARMON ROAD BOOSTER -MOTOR PANEL [REV:DEFAULT] • CONTROL PANEL SIZE: H= 60" W+D= 3612" FEET= 12" TOTAL HEIGHT= 72" • SCADA INTEGRATION: INCLUDED • SPECIFIED KAIC: NONE SPECIFIED • VOLTAGE MONITOR • UPS BACKUP • WIRELESS CAPABLE- Modem provided - No service included • UL Listed and Labeled (UL 508A) • Ethernet Capable for Internet Access • Clock Start Relay; 24vac (or 120vac) • System Fault Logger • VFD Sleep By Flow; Wake By Pressure • Adjust VFD Sleep Settings on HMI • Single Motor Controller • Single Main +Jockey Controller • Multi -Motor Controller with Alternation • EMAIL Alarm Capability • Hand/Off/Auto Selector • Manual VFD Speed Control - Dial (Potentiometer) • Labeled Field Terminal Wiring Strip • Main -Line Slow Fill Routine • HMI Password Protection • PID Set -Point Trimming via Level/Intake • Trend Data logging with upload to USB MECHANICAL DETAIL! PIPE COMPOSITION: STEEL A53 ASTM A53 GROUP B STEEL PIPE BASE COMPOSITION: GALVANIZED ASTM A36 STEEL PLATE - BREAK PRESS FOLDED - HOT DIP GALVANIZED GENERAL DETAILS: • PUMP CHECK VALVE(S) GLOBE - Valmatic, 1800 Silent - Flanged • PUMP ISOLATION VALVES(S) NSF - LUG STYLE BFV • STATION ISOLATION VALVES(5) NSF - LUG STYLE BFV • PRESSURE CLASS: AWWA D [175 PSI] • PRESSURE RELIEF VALVE 6" ClaVal 50-13 COATING DETAILS: Pipe Interior: AWWA/NSF 61 DARK BLUE 7-2540 Pipe Exterior: AWWA/NSF 61 DARK BLUE 7-2540 Skid Base: GALVANIZED Enclosure: N/A SENSORS • Suction Pressure Gauge 1 NSF: 4" Bourdon Tube, SS Case Liquid Filled PSI = -30 +30 • Discharge Pressure Gauge 1 NSF: 4" Bourdon Tube, SS Case Liquid Filled PSI = 0-100 • Suction Pressure Transmitter 1 0 PSI = 0 • Discharge Pressure Transmitter 1 0 PSI = 0 OTHER • Intake Screen Supply Valve NO • 3/4" Air Release Valve 3 • All bare carbon steel is coated with Polyester TGIC baked on powder coating • Hose bib connection (where applicable) • Sample Tap for Potable Systems (where applicable) • Manifold drains (where applicable) ZONE INDUSTRIES MODEL:CB##C2C100X04175-031XXXX4831AS-24 • FLOODED SUCTION J:I:l ill:lu lat'lN INITIAL: DESIGN POINT: 1 DESIGN FLOW RATE (GPM): 4175 INTAKE PRESSURE (PSI): n/a STATION PRESSURE (PSI): 31.16 DISCHARGE PRESSURE (PSI): 31.16 WET WELL DEPTH (FEET): 0 'NNNwrNIN.•INI , • 1 INITIAL: VOLTAGE: 480 PHASE: 3 DISCONNECT AMP RATING NEC FLA Hz: 60 400 279 IJIIitl 11a:1�711ulIrrU: INITIAL: FUNCTION QTY HP PERFORMANCE PUMP TYPE/ MOTOR ENCLOSURE RATING MAIN/DUTY 2 100 4175 GPM @ 72' TDH END -SUCTION CENTRIFUGAL CUP I l:r r N N 1:1 MIRhill r 101ll. INITIAL: MATERIALS COATINGS PIPING: STEEL A53 PIPE INTERIOR: AW WA/NSF 61 DARK BLUE 7-2540 SKID: GALVANIZED PIPE EXTERIOR: AW WA/NSF 61 DARK BLUE 7-2540 SKID BASE: GALVANIZED ENCLOSURE: N/A IULYYNNhl NR111:1.'rrrrlrrlUdll1111N11a1 W INI� I authorize PPS to make material changes to equal or better quality components, as ❑ YES market availability allows, in order to minimize my project lead time ❑ NO I understand that material lead times are currently unreliable and accept that. only want the material that was approved per submittal Vertical Multistage pumps (where utilized) require that intake water be free of suspended sohds. Failure to adequately prescreen can result in seaere pump damage HARMON ROAD BOOSTER You must initialALL sections above andprovide signature & date below to complete submittal approval process. 60% FINAL MAJOR COMPONENT APPROVED BY: 11/08/2023 DATE: ABOUT PPS State of the Art Extensive Pump Manufacturing Station Testing Facility Facilities �= PPS automation • pumping systems VFD/ Automation Large Inventory of Testing Facility replacement equipment & parts Family Owned & Operated Since 1972 For over 100 years, the Purdy Family has been involved in agricultural irrigation and irrigation/municipal water system sales. The core staff of PPS has been here from the very beginning. We have decades of accumulated knowledge in our field. We take great pride in the products, support, and services we offer. Leaders in Variable Speed Pumping Technology h - PPS has been integrating VFD's with Pumps for 40 years. We use the latest technology to create simpler, safer, and more efficient systems. PPS was one of the first pump station manufacturers to effectively implement programmable logic controllers to achieve this goal. Easy to understand, Easy to operate touch -screens on every system. Unparalled Service & Support Personal Service Available 24/7 Free Remote Technical Support for the Life of the System 3 Year Standard Warranty Professional Start-up & Training Services Collaborative Design PPS uses the latest software to design perfectly accurate, top quality pump station designs to ensure premium performance and quality. Precise dimensions and site layout for guaranteed ease of installation. PPS will work directly with site contractors before delivery to ensure an easy and successful installation. Precision Pumping Systems (iTIF� 4F. FQ 6515 S Business Way Boise, ID 83716 (208) 323 - 5300 0 �, MPP www.gopps.us Precision Pumping Systems 6515 South Business Way Boise, ID 83716 Phone: 208-323-5300 PS Fax:208-323-5311 automation - pumping systems Certifications Quality Management System - ISO 9001:2015 PPS Complies with the requirements of ISO 9001:2015 for the manufacturing of `�FtT I F/FO pumping systems, pump control panels, and remote monitoring control systems. Certificate No: CERT-0138890 File No: 1694007 Issue Date: March 31, 2021 Certificate Expiry Date: March 27, 2024 �oMPP�J Safety Management System - (UL 508A / UL QCZJ) UL 508A - Standard for Industrial Control Panels: This certifies that the control panel complies with nationally recognized safety standards. PPS manufactures Control Panels in accordance with the National Electrical code, NFPA 70. File #: E210861 UL QCZJ - Packaged Pumping Systems: L This certifies that the complete pumping system, including the control panel, complies with nationally recognized safety standards. PPS manufactures Packaged Pumping Systems in accordance with Article 680 or 682 of ANSI/NFPA 70, "National Electrical Code" (NEC). File #: E327721 In addition to these safety and quality certifications, each pump station undergoes a complete factory dynamic test to ANSI/HI 14.6 and ANSI/HI 9.6.4 standards and specifications. www.GoPPS.us &ONLINE CERTIFICATIONS DIRECTORY Paae Bottom NITW.E210861 Industrial Control Panels Industrial Control Panels See General Information for Industrial Control Panels PRECISION PUMPING SYSTEMS 6515 BUSINESS WAY BOISE, ID 83716 USA Industrial control panels. Last Undated on 2009-05-01 E210861 Ouestions? Notice of Disclaimer Pace Too Coovriaht n 2009 Underwriters Laboratories Inc.@ The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow -Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non -misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright 2009 Underwriters Laboratories Inc.@" An independent organization Working for a safer world with integrity, preclslon and knowledge_ &ONLINE CERTIFICATIONS DIRECTORY Paae Bottom QCZJ.E327721 Packaged Pumping Systems Packaged Pumping Systems See General Information for Packaged Pumnino Svstems PRECISION PUMPING SYSTEMS 6515 BUSINESS WAY BOISE, ID 83716 USA E327721 Packaged pumping systems, Designated Titan series Cat. Nos. T - Turbine series, followed by additional letter and/or numbers; S - Submersible series, followed by additional letter and/or numbers; CB - Series, followed by additional letters and/or numbers; VMS - Series, followed by additional letter and/or numbers; V - Series, followed by additional letter and/or numbers. Last Undated on 2009-05-29 Ouestions? Notice of Disclaimer Page Top Convrioht Cc) 2009 Underwriters Laboratories Inc.(R) The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow -Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non -misleading manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright 2009 Underwriters Laboratories Inc.@" An Independent or9anizatIorr working tar a safer world with Integrity, precision and knowledge_ CERTIFICATE OF REGISTRATION This is to certify that Purdy Enterprises, Inc. Precision Pumping Systems 6515 Business Way, Boise, Idaho 83716 USA operates a Quality Management System which complies with the requirements of ISO 9001:2015 for the following scope of certification Design and manufacture of pumping systems, pump control panels, and remote monitoring and control systems. Certificate No.: CERT-0138890 File No.: 1694007 Issue Date: March 31, 2021 Frank Camasta Global Head of Technical Services SAI Global Assurance A C C Ft E D I T E D MANAGEMENT SYSTEMS ISO 9001 CERTIFICATION BODY Original Certification Date: Certification Effective Date Certificate Expiry Date: BAR 4F MULTJLgrFR �9 ti Q�N�TlON ARRANS'��= March 29, 2018 March 28, 2021 March 27, 2024 Registered by: Terms a Canada Limited (SAI Global), , 20 Carlson Cord, Suite skill w Toronto, ed in C M9W out Canada. This t, SAI Global a subject to the SAI Global SAI G LO BA L Terms and Conditions for Certification. While all due care and skill was exercised in cerrying out this assessment, SAI Global accepts responsibility only for proven negligence. This certificate remains the property of SAI Global and must be retumed to them upon request. To verify that this certificate is current, please refer to the SAI Global On -Line Certification Register INFORM. INSPIRE. IMPROVE. httos://wunvsaialobal.com/en-us/assurance/auditina and rertifcatinn/certificatinn mnishv/ O 01 101" _ 4w I I PLAN VIEW NEC CLEARANCE SEE LOCAL CODES 16" DISCI FRONT V 47 M K 2 6" PRV DISCHARGE TO ATMOSPHERE, PIPING (BY OTHERS) 1 DESIGN SPECIFICATIONS Design Flow Rate: 4175 GPM @ 31.2PSI Boost Duty Pump Details: 100 HP/Pump I 4175 GPM @ 72 TDH Minimum Power: 480 Volt / 3 Phase Model# CB##C2C10OX04175-031XXXX4831AS-24 ITEM NO. DESCRIPTION Size CITY. 1 CONTROL PANEL 72"x60"xl8" 1 2 MOTOR, 1800 RPM, ODP 100 HP 2 3 PRESSURE GAUGE, 100 PSI, NSF 4" 1 4 PRESSURE TRANSDUCER,- 2 14.5-145PSI, NSF 5 PUMP, CENTRIFUGAL, CORNELL 10RB 2 6 SAMPLE TAP 1/2" 1 7 SKID, BENT 96"xl44' 1 8 VACUUM/PRESSURE COMBO 4" 1 GAUGE 9 VALVE, AIR RELIEF 3/4" 3 10 VALVE, BUTTERFLY, LUG, 250 PSI 16" 4 11 VALVE, BUTTERFLY, LUG, LEVER, 6" 2 250 PSI 12 VALVE, CHECK, SILENT, GLOBE 16" 2 13 VALVE, PRESSURE RELIEF, ANGLED 6" 1 DUTY PUMP END VIEW MATERIAL TITLE. BOOSTER SYSTEM SUCTION ���/` / �p/�SVV 11P110STEEL All, NSF NAPGUARD BLUE Vd.STEELA36,GALVANIZED PUMP STATION NO ENCLOSURE UNLESS OTHERWISE SPECIFIED: PROJECT. HARMON ROAD BOOSTER DIMENSIONS ARE IN INCHES COLOR - N/A PRECISION PUMPING SYSTEMS TOLERANCES: EVEL' 60% Pre -Final POTABLE 6515 BUSINESS WAY BOI3E,lDAH063716 ONE PLACE DECIMAL: !.10 woPucEDecIMAc.os sAoSMAN: PART No: 2C-24-NJ-XX-NF-FM-NI-PT NOT FOR FABRICATION 208-323-5300 U —W.gopPS.U5 .L DO NOTSCALEDRAWING DRAWN: RAS I DATE: 11/7/2023� .JOB: (SIZE. BISCALE: NTSISHEET. 1 OF 1 IRDEFAULT 3 2 1 1 OW 01 O u N MicroSmart FC6A Plus PLC CPU Module Specifications ID DEC ;PRODUCT DESCRIPTION :This next -generation IDEC MicroSmart ;FC6A Plus PLC performs beyond micro ;PLC limits. With its 2,060 1/0 capacity, .it can control large machines or entire small-scale manufacturing facilities, :providing more capabilities for the most demanding applications. :KEY FEATURES �• Dual Ethernet ports FC6A PLUS CPU MODULES • iOS and Android WindEDIT app High-speed Counter 1/0 ;• Maximum 2,060 digital 1/0 Part No. & Pulse Output Power Input Output Interface Points ; • Maximum 511 analog 1/0 FC6A-D16R10EE Relay Output 2A (240V AC-2A, 30V DC-2A) �• Bluetooth communication FC6A-D16P10EE • High-speed counter Transistor Source Output 0.5A Port 1 (USB) 16 points '• BACnet/IP and ModbusTCP Maximum input (8/8) frequency:100kHz 24V DC Port 2 , FC6A-D16K10EE 24V DC (Sink/ Transistor Sink Output 0.5A (Ethernet) FC6A-D32P3CEE • Pulse output Source) Maximum output frequency:100kHz Port 3 Transistor Source Output 0.1A (Ethernet) , ' C E O 32 points C o us (16/161 � FC6A-D32K3CEE Transistor Sink Output 0.1A ' Classl Div2 ABS SPECIFICATIONS .. TIDE APPROVAL PROGRAM Part No. FC6A-D16R10EE FC6A-D16P10EE FC6A-D32P3CEE , FC6A-D16K10EE FC6A-D32K3CEE Rated Power Voltage 24V DC Allowable Voltage Range 20.4 to 28.8V DC (including ripple) FC6A-D1 6R1 CEE. 2.88W (24V DC) ; Maximum Power FC6A-D16P10EE 2.88W (24VDC) Consumption FC6A-D16K10EE 2.88W (24VDC) (CPU module) FC6A-D32P3CEE 3.36W (24V DC) FC6A-D32K3CEE. 3.36W (24V DC) , Inrush Current 35Amaximum ' Allowable Momentary Power Interruption 10ms (at rated voltage) ; Operating Temperature —10 to+55°C (no freezing) Storage Temperature —25 to+70°C (no freezing) Relative Humidity Level RH1 (IEC 61131-2)10 to 95% (no condensation) , Altitude Operation: 0 to 2,000m, 795 to 1,013hPa, Transport: 0 to 3,000m, 701 to 1,013hPa ; Pollution Degree 2 (IEC 60664-1) Corrosion Immunity Free from corrosive gases Between power and FE terminals: 500V AC, 1 minute Between input and FE terminals500VAC, ' Between transistor output and FE terminals: 500VAC, 1 minute 1 minute Between relay output and FE terminals: 2,300V AC, , Dielectric Strength Between power and input terminals: 500V AC, 1 minute , 1minute Between power and transistor output terminals: 500V AC, Between power and relay output terminals: 2,300V AC, 1 minute 1 minute Between input and transistor output terminals: 500V AC, ' Between input and relay output terminals 2,300VAC, 1 minute 1 minute K 2 SPECIFICATIONS CONT. USB PORT SPECIFICATIONS Between power and FE terminals: USB Type USB mini-B 100MO or higher (500V DC megger) Between input and FE terminals' USB Standard USB 2.0 Between transistor output and FE terminals: 100M0 or higher (500V DC megger) 100MO or higher (500V DC megger) Between relay output and FE terminals: Isolationcircuit Not isolated from the internal Insulation Resistance Between power and input terminals: 100MfZ or higher (500V DC megger) 100MO or higher (500V DC megger) Between power and transistor output terminals: Maintenance communication to Between power and relay output terminals: 100 MO or higher (500V DC megger) Communication Function PC 100 M0 or higher (500V DC megger) Between input and transistor output terminals: Between input and relay output terminals: 100 MO or higher (500V DC megger) 100MO or higher (500V DC megger) ETHERNET PORT 1 SPECIFICATIONS Noise Resistance AC/DCpowerterminals 1kV,50nsto1ps 1/0 terminals (coupling clamp). 1.5kV, 50ns to 1ps coupling adapter Communication Type IEEE802.3 compliant Vibration Resistance 5 to 8.4Hz amplitude 3.5mm 8.4 to 150Hz acceleration 9.8m/s (11G), 2 hours per axis on each of three mutually perpendicular axes Communication Speed 10BASE-T,100BASE-TX (IEC 61131-2) Connector RJ45 Shock Resistance 147m/s' (15G), 11 ms duration, 3 shocks per axis on three mutually perpendicular axes Cable CAT.SSTP Degree of Protection IP20 (IEC 60529) Power Supply Wire UL1007 AWG24-16, UL2464 AWG24-16, UL1015 AWG20-16 Maximum Cable Length 100m Grounding Wire UL1007 AWG16 Isolation Pulse transformer isolation Ground D-type ground (Class 3 ground) Maintenance communication (server), Communication user communication (server/client), Mounting DIN rail or panel mounting Function user communication UDP, Modbus TCP (server/client), Email, Web Server, PING, FC6A-D16R10EE. 290g FC6A-D32P3CEE: 255g SNTP, FTP server/client, BACnet/IP server Weight(approx.) FC6A-D16P10EE 275g FC6A-D32K3CEE:255g FC6A-D16K10EE 275g ETHERNET PORT 2 SPECIFICATIONS FUNCTION SPECIFICATIONS Communication Type IEEE802.3compliant Communication Speed 10BASE-T,100BASE-TX FC6A-D16R10EE FC6A-D32P3CEE(*4) Part No. FC6A-D16P10EE(*4) FC6A-D32K3CEE(*4) Connector RJ45 FC6A-D16K1 CEE (*4) Cable CAT.SSTP Control System Stored program system Maximum Cable Length 100m Basic 42 Instruction Words Advanced 130 Isolation Pulse transformer isolation Program Capacity (1) 800KB (100,000 steps) Maintenance communication (server),user User Program Storage Serial Flash Memory (100,000 times rewritable) Communication Function communication (server/client), user communication UDP, Modbus TCP Basic Instruction 21 ps/1,000 steps (server/client), PING Processing Time END Processing (*2) 1 ms maximum Input 8 points 16 points 1/0 Points Output 8 points 16 points Expandable Modules 7 modules (*3) Expandable 1/0 Points with Expansion Modules 224 points Expandable Modules with Unibody Type Expansion 8 modules Modules Expandable 1/0 Points with Unibody Type Expansion 256 points Modules Expandable Modules with Separate Type Expansion 63 modules (separate type master: 1 module maximum, separate type slave 10 Modules (*5) modules maximum) Expandable 1/0 Points with Separate Type Expansion 2,016 points Modules (5) Internal Relay 15,400 points Special Internal Relay 1,600 points Shift Register 256 points Data Register 60,000 points Non -Retentive Data Register 200,000 points Special Data Register 900 points Counter 512 points Timer (1ms, 10ms,100ms,1s) 2,000 points Clock Clock accuracy: ±30 sec/month (typical) at 25°C Backup Data Internal relay, shift register, counter, data register, timer, special data register, special internal relay, clock data RAM Backup Battery Lithium primary battery (BR2032) Battery Life Approx. 4 years Replaceability Possible Keep data, user program sum check (serial flash memory), user program sum check Self -diagnostic Function (RAM), timer/counter preset value sum check, user program syntax check, user program execution check, WDT check, user program write check, power failure, clock error, data ink connection check, 1/0 bus initialization check Input Filter 0 ms (without filter), 3 to 15ms (selectable in increments of 1ms) 114, 115, 116, 117: 3ms Six inputs Catch Input/Interrupt Input 10,11,13,14,16,17 (Minimum turn on pulse width 5ps max./Minimum turn off pulse width. 5ps max.) ■ 2 1111►reIIQ01&1Jx71a[7_AtIII MLlRK11183 1110 Maximum Counting Frequency and High- Total 6 points Single/two-phase selectable 100kHz (single-phase: 6 points, two-phase: 3 points) High-speed Counter speed Counter Points Counting Range 0 to 4,294,967,295 (32 bits) Operation Mode Rotary encoder mode, adding counter mode, frequency measurement mode Quantity 1 point Analog Potentiometer Data Range 0 to 1,000 Quantity 1 point Input Voltage Range 0 to 1 OV Analog Voltage Input Input Impedance Approx.100KO Digital Resolution Approx. 4,000 steps (12 bits) Quantity 4 points Pulse Output Maximum Output Pulse Frequency Q0, Q2, 04, 06: 100kHz (transistor output model only) Reversible Control Single -pulse output mode: 4 axis (GO-Q7), Dual -pulse output mode: 4 axis (GO-Q7) PWM Output Duty cycle 0 1 to 100.0% (increments of 0.1 %), Output pulse frequency 15 to 5,000 Hz (increments of 1 Hz): 4 points (00, Q2, Q4, Q6) (Adjust 5ps minimum as ON time and 15ps minimum as OFF time.) USB Port USB mini-B (maintenance communication) Ethernet Port 1 Maintenance communication (server), user communication TCP (server/client), user communication UDP, Modbus TCP (server/client), Email, Web Server, PING, SNTP, FTP server/client Ethernet Port 2 Maintenance communication (server), user communication TCP (server/client), user communication UDP, Modbus TCP (server/client), PING Cartridge (option) Two cartridges can be added (when using FC6A—HPH1)/One cartridge can be added (when using FC6A—PH1) SD Card Slot Embedded HMI Module (option) Yes *11 step equals 8 bytes *2. Not including expansion 1/0 service time, counter timer processing time, data link processing time, and interrupt processing time. *3. A maximum of 5 modules can be connected when using the expansion interface module separate type master. *4. Transistor output model *5' Communication module cannot be connected INPUT SPECIFICATIONS Part No. FC6A-Di6R10EE FC6A-D32P3CEE FC6A-D16P10EE FC6A-D32K3CEE FC6A-D16K10EE Input Points 8 (8/1 common) 16 (16/1 common) Rated Input Voltage 24V DC:24V DC sink/source input signal Input Voltage Range 0 to 28.8V DC Rated Input Current High speed input port 5mA/pt, middle/normal speed input port 7mA/pt Input Impedance High speed input port 4.9kO, middle/normal speed input port: 3.40 High speed input port' 5ps+filtervalue Turn ON Time Middle speed input port: 35ps + filtervalue Input Delay Normal speed input port. 35ps+filtervalue High speed input port. 5ps+filtervalue Turn OFF Time Middle speed input port: 35ps + filtervalue Normal speed input port' 100ps+filtervalue Isolation Between input terminals: Not isolated Internal circuit: Optocoupler-isolated Input Type Type1 (IEC 61131-2) External Load for I/O Interconnection Not needed Signal Determination Method Static Effect of Improper Input Connection Both sinking and sourcing input signals can be connected, therefore reverse connection does not cause damage. If any input exceeding the rated value is applied, permanent damage may be caused. Cable Length 3m in compliance with electromagnetic immunity Insertion Durability 100 times minimum Connector Applicable Ferrule 1-wire: Al 0 5-8 WH (Phoenix Contact) 2-wire: AI -TWIN 2xO 5-8 WH (Phoenix Contact) RELAY OUTPUT SPECIFICATIONS Part No. FC6A-D16R10EE Relay Output Points 8 Output Points per COM1 4 Common Line COM2 4 Output Type 1 NO Per Point 2A Maximum Load Current COM1: 7A Per Common COM2: 7A Minimum Switching Load 1 mA/5V DC (reference value) Initial Contact Resistance 30mO maximum RELAY OUTPUT SPECIFICATIONS CONT. Electrical Life 100,000 operations minimum (rated resistive load 1,800 operations/hour) Mechanical Life 20,000,000 operations minimum (no load 18,000 operations/hour) Rated Load Resistive load 240V AC 2A, 30V DC 2A Inductive load. 240V AC 2A (cos to = 0.4), 30V DC 2A (UR =7 ms) Insertion/Removal 100 times minimum Durability Connector 1-wire: Al 0 5-8 WH (Phoenix Contact) Applicable Ferrule 2-wire: AI -TWIN 24.5-8 WH (Phoenix Contact) TRANSISTOR OUTPUT SPECIFICATIONS Pert No. FC6A-C16P10EE FC6A-D32P3CEE FC6A-C 1 6K10EE FC6A-D32K3CEE Transistor Output Points 8 (8/1 common) 16 (16/1 common) Transistor Sink FC6A-Di6K10EE/FC6A-D32K3CEE Output Type Transistor Source FC6A-DI6PiCEE/FC6A-D32P3CEE Rated Load Voltage 24V DC Voltage Tolerance 19.2 to 28.8V DC Rated Load Per Point 0.5A 0.1A Current Per Common 4.OA 1.6A Turn ON Time High speed input port 5ps Normal speed input port: 300ps Output Delay Turn OFF Time High speed input port. 5ps Normal speed input port: 300ps Isolation Between output terminal and Internal circuit Optocoupler-isolated Between output terminals: Not isolated Voltage Drop (ON Voltage) 1V max (voltage between COM and output terminal when output is on ) Inrush Current 1A 0.2A Leakage Current 0.1mA maximum Clamping Voltage 39V±1V Maximum Lamp Load 12W 2AW Inductive Load L/R=10ms (28.8V DC,1Hz) Overcurrent Protection Transistor Sink Output: No Transistor Source Output: Overcurrent is detected by current limit resistance. (1) External Current Draw 100mA maximum, 24V DC (power voltage at the+V terminal, -V terminal at source) Insertion Durability 100 times minimum Connector Applicable Ferrule 1-wireAl 0.5-8 WH (Phoenix Contact) _ 2-wire. AI -TWIN 24.5-8 WH (Phoenix Contact) ■ *1. This overcurrent signals consist of one signal per 4 point outputs. When microprocessor gets this overcurrent signal by interrupt input, microprocessor turns off 4pt outputs of this category at fixed time (approx.1sec). DIMENSIONS (mm) FC6A-D16R10EE FC6A-D16K10EE FC6A-D16P10EE 130.9 114.3 73.0 �1 oo� �J Qo 4.0 av � eml QO % Ur I FC6A-D32K3CEE 130.9 FC6A-D32P3CEE 114.3 T 70.0 8.2 73.0 \ � Qo LE ao 4.0 oo TIM Qo Qo em em ea em Ur a""P� WDEC IDEC Corporation 1175 Elko Drive • Sunnyvale, CA 94089. 800-262-IDEC (4332) Fax: 408-745-5258 www.IDEC.com/usa ©20181DEC Corporation. All Rights Reserved. FC9Y-DS400-1 9/18 7.5K 7" HMI HG2J Series Sleek. Stylish. Smart. GENERAL SPECIFICATIONS Rated Power Voltage 12 to 24V DC Power Voltage Range 10.2 to 28.8V DC Power Consumption 13W maximum 5W maximum when not using USB1 or USB2 3W maximum when Backlight OFF Allowable Momentary 10ms max. (power supply voltage 20.4 to 28.8V DC) Power Interruption 1ms max. (power supply voltage 10.2 to 20.4V DC) Inrush Current 30A maximum Dielectric Strength 500V AC, 10 mA,1 minute between power and FG terminals Operating Temperature -20 to+60°C (no freezing) Operating Humidity 10 to 90%RH (no condensation) Storage Temperature -20 to+70°C (no freezing) Storage Humidity 10 to 90%RH (no condensation) Pollution Degree 2 Vibration Resistance 5 to 8.4 Hz single amplitude 3.5 mm, 8.4 to 150 Hz acceleration, 9.8M/s2 on each of three mutually perpendicular axes (IEC61131-2) Shock Resistance 147m/s2, 11ms, 5 shocks on each of three mutually perpendicular axes ((IEC61131-2) Noise Immunity Fast transient/burst test Power terminals: 2 kV Communication line: IkV (IEC/EN61131-2) Electrostatic Discharge Contact: 6 kV Air. 8kV (IEC/ENG1131-2) Corrosion Immunity Free from corrosive gases Mounting Panel mount (panel thickness: 1.0 to 5.0 mm) Degree of Protection When panel thickness is less than 1 to 5mm: IP66F (IEC60529) When panel thickness is less than 1.6 to 5mm: IP66F, IP67F (IEC60529) TYPE 4X, TYPE 13 Dimensions 186 (W) x 128 (H) mm x 30.4 (Dj mm Weight (approx.) 500g Do not use the HG2J in an environment subject to strong ultraviolet rays, otherwise the LCD quality will deteriorate i1DEC PRODUCT DESCRIPTION Stylish smart capacitance touchscreens with an input voltage of 12-24V DC make the HG2J HMI a leading choice for applications across a variety of industries, including industrial, solar, and vehicle applications. Offered in a popular size form factor, HG2J uses Projected -Capacitive (PCAP) technology to provide a slimmer and sleeker appearance, small installation footprint, improved performance, and longer life. An industry -leading three year warranty and exceptionally wide operating temperature range, as well as IP66/67F, Type 4X, 12, 13, and Class I Div 2 approval ratings, assure reliable operation even in the toughest environments. KEY FEATURES • 800 x 480 High Resolution • 50,000 Hours Backlight Life • 500 cd/m2 Brightness • -20 to +60°C Extreme Operating Temp • Remote Access, FTP, Email, Mobile App and Custom Web Page • Support 4 protocols simultaneously OS E �, .55, o�z c A DISPLAY SPECIFICATIONS OPERATION SPECIFICATIONS Display TFT color LCD (TN type) Color / Shade 65,536 colors (16-bit color) Effective Display Area 154.08 (W) x 85.92 (H) mm Display Resolution 800 (W) x 480 (H) pixels DPI 0.1926 (W) x 0.179 (H) mm View angle Left/right/top: 80°, bottom 60' Backlight White LED Backlight Life 50,000 hours minimum (* 1) Brightness 500 cd/mz (Typ.) (*2) Brightness Adjustment 48 levels Backlight Replacement Not replaceable by user (must be replaced by IDEC) Font Shift_JIS (Japanese) ANS11250 (Central European IS08859-1 (European) language) GB2312 (Simplified Chinese) ANS11251 (Baltic) BIG5(Traditional Chinese) ANS11251 (Cyrillic) KSC5601 (Korean) ASCII (7-seg) Character Size 8 to 512 Character Attribute Blink (1 or 0.5 sec period), reverse Graphics Straight line, polyline, rectangle, circle, arc, circle/ellipse, equilat- eral polygons (3, 4, 5, 6, 8) picture Window Display 3 popup screens + 1 system screen *1) The backlight life is not guaranteed and refers to the time until the brightness reduces by half after use at 25°C The actual life depends on operating environments and conditions *2) Brightness of the LCD alone at an ambient temperature of 25°C Switching Element PCAP (Projected capacitance) method Multiple Operations Up to 2 points Acknowledgement Sound Electronic buzzer or audio output FUNCTION SPECIFICATIONS Screen Types Base screen, popup screen, system screen No. of Screens Base screen: 3,000 max. Popup screen: 3,015 max. User Memory Approx. 24MB Parts Bit Button, Word Button, Goto Screen, Print Button, Key Button, Multi Button, Keypad, Numerical Input, Character Input, Pilot Lamp, Multi -State Lamp, Picture Display, Message Display, Message Switching Display, Alarm List Display, Alarm Log Display, Data Log Display, Numerical Display, Bar Graph, Trend Chart, Pie Chart, Meter, Calendar, Bit Write Command, Word Write Command, Goto Screen Command, Print Command, Timer, Screen Script Command, Multi Command Calendar Year, Month, Day, Hour, Min., Sec., Day of Week±90 sec per month (at 25°C) Power Failure Backup Calendar, log data, keep relay, internal register Data Backup Time 20 days (Typ.) (*3) *3) If the power is cut off for more than 20 days, the error message 'Backup data lost" will be displayed at the next start-up and the clock data will be initialized to "00.00.00 January 1, 2000". TOUCHSCREEN PART NUMBER ACCESSORIES Part Number Display Type Bezel Color Part Number Description Quantity HG2J-7UT22TF-B 7" TFT Color LCD, Projected Black SW1A-W1C Automation Organizer Software 1 Capacitive Touchscreen HG9Z-4K2PN04 � Mounting Clip 4 HG9Z-XT09P Serial Interface, Removable QZ7 Push -in Connector 1 I= HG9Z 2D7PN05 Protective Sheets 5 DIMENSIONS (mm) PANEL CUT-OUT 186.0 56 176.2 175 6 ooB o 000000000�0�00000000 o ao� ��0 000000 ° ° 000000 00 - --------------------- i ,_, ° o00000000000000000000�, oo f 000 00000000u0000000000 0 Panel Thickness:1.0 to 5.Omm All dimensions in mm. 0 oee eeo ry r o Dimensions in blue show the mounting dimensions of the cable. Dimensions in the figure may vary depending on the type of cable connected. The information listed here should be used as a guide for reference when designing. Install the operator interface into a panel cut-out by tightening the six mounting clips (supplied with the operator interface) to a torque of 0.5 to 0.6 N.m. Do not tighten with excessive force, otherwise the operator interface may become distorted. Also, waterproof characteristics may be lost. DEC IDEC Corporation • 1175 Elko Drive • Sunnyvale, CA 94089. 800-262-IDEC (4332) Fax: 408-745-5258 https:Hus.idec.com M@2022 IDEC Corporation. All Rights Reserved. HG9Y-DS200-A-O 03/08 PDF Only m CORNELL Pump: Fluid: Size: 10RB Dimensions: Suction: 10 in Name: Water Type: Clear Liquids Discharge: 10 in SG: 1 Vapor Pressure: 0.256 psi a Synch Speed: 1800 rpm Density: 62.4 lb/ft' Atm Pressure: 14.7 psi a Line: 11.88" x 13' Viscosity: 1.1 cP Curve: 1ORB18 Temperature: 60 °F Margin Ratio: 1 Pump Limits: Temperature: 250 °F Sphere Size: 1.25 in Search Criteria: Wkg Pressure: 155 psi g Flow: 4175 US gpm Near Miss: ___ Head: 72 ft Static Head: 0 ft Motor: Standard: NEMA Size: 100 hp Enclosure: CDP Speed: 1800 rpm Frame: 404T Sizing Criteria: Design Point Pump Selection Warnings: None --- Duty Point --- Flow: 4237 US gpm Head: 74.1 ft Eff: 80.6% Power: 98.1 hp NPSHr: 18 ft Speed: 1785 rpm --- Design Curve --- Shutoff Head: 131 ft Shutoff dP: 56.5 psi Min Flow: 500 US gpm BEP: 81.7% @ 3924 US gpm NOL Power: 98.8 hp @ 4681 US gpm 200 13 50" x 0° 70 75 150 85` 11.88" x 13` _ _ T -__ �7� --87 100 81.7 hr 75� 0 75 150 1p 50 125 hp 75 70 I LL Li, --- Max Curve --- 0 Max Power: 40 187 hp @ 5688 US gpm = 20 to — - a z o 50b 10)0 1500 20b0 2500 3000 3500 4000 4500 5000 55)0 Min flow line represents the absolute lowest flow pump can operate. For flow rates to the left of the first efficiency line on the curve, consult your Cornell Sales representative. Actual efficiency and HP may vary depending on mounting configuration. Refer to Catalog curve. US gpm Selected from catalog: Cornell.60, Vers 3.15.0 Company: Name: �T Date: 11/06/2023 CORNELL Performance Evaluation: Flow Speed Head Efficiency Power NPSHr rpm % 5010 1785 --- --- --- --- 4175 1785 75.4 81 98 17.9 3340 1785 88.8 78 95.4 16.6 2505 1785 100 67 93.9 15.3 1670 1785 109 49 92.6 14 Selected from catalog: Cornell.60, Vers 3.15.0 ai 61!14 MMIO Cage -Protected Level Transmitters Designed for severe high solids environments such as . sewage, lift stations, storm canals, wet wells and slurry tanks where sludge, slurry or turbulence may be present. 3-YEAR WARRANTY • Features large 3" non -fouling sensing area Welded at cap and base to provide a leak -proof seal • Highly accurate, shock -resistant and extremely stable over long periods of time Electrical surge, noise and reverse polarity protected Pressure Gauges Vacuum and pressure from 10 inH20 through 145,000 psig, as well as differential pressure. 100 3-YEAR WARRANTY rW"'LST� ' Dial indicating, process, digital and differential gauges 1 Multiple case materials, filling and connection options Vibration, shock, pulsation and chemical -resistant KM • High quality construction including heavy Bourdon tubes for longer life • Liquid -filled and dry configurations available Pressure Transmitters and Transducers NOSHOK pressure transmitters and transducers are available in vacuum, absolute and gauge pressure ranges up to 145,000 psig. 3. 3-YEAR WARRANTY • Vibration and chemical resistant with a full array of commonly used outputs (4 mA - 20 mA, 0 Vdc -10 Vdc, .5 Vdc - 4.5 Vdc, etc.) • Extremely stable zero and span • Front flush diaphragm option for sludge, slurry or high viscosity media • High RFI, EMI & ESD protection Dial Indicating Pressure Gauges ABS & Stainless Steel Liquid Filled 9O� SERIES • Extremely high quality pressure gauges, liquid filled for extended service life and shock resistance • Ranges available from vacuum to 15,000 psi • 1-1/2, 2, 2-1/2, 4 inch sizes - bottom or back connected • Lightweight shatter -resistant ABS case with PlexiglassTM lens for extra strength, or 304 stainless steel case with polycarbonate lens • Unique o-ring case and connection seals guard against leakage and protect against shock and vibration • Relief disc on top or back provides positive case relief • Brass and copper alloy movement • High grade Glycerine fill dampens the effects of pulsation, vibration and shock loads, and provides lubrication of the movement • Volume oriented • Stock availability OPERATING SPECIFICATIONS 1. Working Pressure Limitations a. Dynamic Pressure MODELS SPECIFICATIONS The working pressure should be limited to 60% of the dial range Case 15-910, 25-900, 25-910 ABS (Acryl Nitril Butadien Styrol) b. Static Pressure 25-901, 25-911, 40-901, 40-911 304 Stainless steel The working pressure, when no sharp Bezel 25-901, 25-911, 40-901, 40-911 304 Stainless steel fluctuations occur, should be limited to Lens 15-910, 25-900, 25-910 Plexiglass"; ultrasonically welded to the case 90% of the dial range. 25-901, 25-911 Polycarbonate 2. Ambient Temperature 40-901, 40-911 Instrument glass 4°F to 140°F (20°C to 60°C) Glycerine Fill Bourdon Tube 15-910, 25-900, 25-910, 25-901, 25-911, Phosphor bronze "C" tube -40°F to 140°F (-40°C to 60°C) Special Fill 40-901, 40-911 (up to 600 psi) 3. Media Temperature 15-910, 25-900, 25-910, 25-901, 25-911, Coiled safety tube -4°F to 140°F (-20°C to 60°C) Glycerine Fill 40-901, 40-911 (greater than 600 psi) -40°F to 140°F (-40°C to 60°C) Special Fill Connection 15-910 1/8" NPT brass 25-900, 25-910, 25-901, 25-911, 1/4" NPT brass 40-901, 40-911 1/4" NPT brass or 1/2" NPT brass APPLICATIONS Movement 15-910, 25-900, 25-910, 25-901, 25-911, Brass and nylon with highly polished bearing surfaces ■ Industrial applications where pulsation, vibration and 40-901, 40-911 shock are present Safety Protection 15-910, 25-900, 25-910 Safety relief disc on the back of the case 25-901, 25-911, 40-901, Safety relief disc on the top of the case 40-911 ACCURACY Accuracy 15-910, 20-901, 20-911 ± 2.5% Full Scale ASME grade B 25-900, 25-910, 25-901, 25-911 ± 1.5% Full Scale ASME grade A ■ 1-1/2 and 2 inch 900 Series Gauges: ±2.5% 40-901, 40-911 ± 1% Full Scale ASME grade 1A ■ 2-1/2 inch 900 Series Gauges: ±1.5% Pointer 15-910, 25-900, 25-910, 25-901, 25-911 Molded plastic ■ 4 inch 900 Series Gauges: ±1.0% 40-901, 40-911 Balanced aluminum, black finish Dial 15-910, 25-900, 25-910, Molded plastic, white background with black psi scale and 25-901, 25-911 red kPa scale. UV resistant 40-901, 40-911 Aluminum, white background, dual scale psi - kPa. black psi scale and Red kPa scale. UV resistant Fill Liquid 15-910, 25-900, 25-910, 25-901, 25-911, Glycerine and water For details on accuracy/standard dial configuration 40-901, 40-911 and dial layouts, see pages 74-78 26 9� ORDERING INFORMATION SERIES DIMENSIONS ORDERING INFORMATION SERIES 900 SIZE 15 1-1/2" 20 2" 25 2-1/2" 40 4" CASE TYPE 900 ABS Case, Liquid Filled, Bottom Connection 910 ABS Case, Liquid Filled, Back Connect' 901 SS Case, Liquid Filled, Bottom Connection 911 SS Case, Liquid Filled, Back Connection PRESSURE 30 " Vac -30 inHg to 0 100 0 psi to 100 psi 5000 0 psi to 5,000 psi 10 0 bar to 10 bar RANGES 30/15 -30 inHg to 0 to 15 psi 160 0 psi to 160 psi 6000 0 psi to 6,000 psi 16 0 bar to 16 bar 30/30 -30 inHg to 0 to 30 psi 200 0 psi to 200 psi 7500 0 psi to 7,500 psi 25 0 bar to 25 bar 30160 -30 inHg to 0 to 60 psi 300 0 psi to 300 psi 10000 0 psi to 10,000 psi 40 0 bar to 40 bar 30/100 -30 inHg to 0 to 100 psi 400 0 psi to 400 psi 15000 0 psi to 15,000 psi 60 0 bar to 60 bar 30/160 -30 inHg to 0 to 160 psi 600 0 psi to 600 psi -1 -1 bar to 0 bar 100 0 bar to 100 bar 30/200 -30 inHg to 0 to 200 psi 800 0 psi to 800 psi 1 0 bar to 1 bar 160 0 bar to 160 bar 30/300 -30 inHg to 0 to 300 psi 1000 0 psi to 1,000 psi 1.6 0 bar to 1.6 bar 250 0 bar to 250 bar 15 0 psi to 15 psi 1500 0 osi to 1,500 psi 2.5 0 bar to 2.5 bar 400 0 bar to 400 bar 30 0 psi to 30 psi 2000 0 psi to 2,000 psi 4 0 bar to 4 bar 600 0 bar to 600 bar 60 0 psi to 60 psi 3000 0 psi to 3,000 psi 6 0 bar to 6 bar 1000 0 bar to 1,000 bar SCALE OPTION psi psi single scale psilkglcm' ps'Ikg/cmz dual scale bar/psi duals i1kPa psillcPa dual scale osi/bar osi/bar dual scale CONNECTION SIZE 1/8 1/8"NPT 1/4 1/4"NPT V2 1/2"NPT 1/4BSPP 1/4"BSPP Steel Panel Mount Clamp WSCR 304SS Cover Ring 304SS Front Flange BP3 Brass Press Fit Orifice 0.3 mm C 30433 Panel Mount Clamp MIP Maximum Indicating Pointer 30433 Rear Flange BT5 Brass Threaded Orifice 0.5 mm SSB-U Stainless Steel Bezel & U Clamp AP Adjustable Pointer LM Laser Marking BT8 Brass Threaded Orifice 0.8 mm SSB Stainless Steel Bezel ' SGL Safety Glass Lens ST Stainless Steel Tagging 7/16" -20 Straight Thread Available' Please consult your local NOSHOK Distributor or NOSHOK, Inc. for availability and delivery information. NOTE: Refer to 900 Series Options & Accessories chart on page 67 for availability by model number. Includes Viton® 0-Ring 25-910 -1000 psi/kPa -1/4 - PMC EXAMPLE 1. Select model number (size & case type) 2. Select pressure range & scale option 3. Select connection size (if more than one is offered) 4. Select any required accessory or option 1.06" (Z7—) 2.48" (63mm) 2 68" (68mm) 2.24" (57mm) — 0. (14mm) T YO55V" (14mm) OUTLINE DIMENSIONS dogma 1.26" (32mm) 0.20" (5mm) 2.44" 2.72" (62mm) (69mm) 2.24" (57mm) 0. 5" 14mm 0.55" T 3.43" (87mm) 2.01" (51 mm) 27 Rosemount 3051 Rosemount 3051 T In -Line Pressure Transmitter 3051T In -Line Wireless Pressure Transmitter This ordering table contains the following Rosemount 3051 T configurations: Configuration Transmitter Output Code 4-20 mA HART' -3051 A -Enhanced 3051(1 FOUNDATIONTM fieldbus F PROFIBUS PA W Wireless X (1) The enhanced 4-20 mA HART device can be ordered with Transmitter Output option code A plus any of the following new option codes: DAO, M4, QT, DZ, CR, CS, CT, HR5, HR7. See Specifications and Options for more details on each configuration. Additional Information Specifications: page 42 Certifications: page 53 Dimensional Drawings: page 60 Table 2. 3051T In -Line Pressure Transmitter Ordering Information * The Standard offering represents the most common options. The starred options (*) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Model Transmitter Type 3051T In -Line Pressure Transmitter Pressure Type Standard Standard G Gage AM Absolute Pressure Range 3051 TG (2) 3051 TA Standard Standard 1 -14.7 to 30 psi (-1.0 to 2.1 bar) 0 to 30 psia (0 to 2.1 bar) 2 -14.7 to 150 psi (-1.0 to 10.3 bar) 0 to 150 psia (0 to 10.3 bar) 3 -14.7 to 800 psi (-1.0 to 55 bar) 0 to 800 psia (0 to 55 bar) 4 -14.7 to 4000 psi (-1.0 to 276 bar) 0 to 4000 psia (0 to 276 bar) 5 -14.7 to 10000 psi (-1.0 to 689 bar) 0 to 10000 psia (0 to 689 bar) Transmitter Output Standard Standard A(3) 4-20 mAwith Digital Signal Based on HART Protocol F FOUNDATION fieldbus Protocol W(4) PROFIBUS PA Protocol X(s) Wireless Process Connection Style Standard Standard 213 1/2-14 NPT Female 266) Glh A DIN 16288 Male (Available in SST for Range 1-4 only) Expanded 2F(7) Coned and Threaded, Compatible with Autoclave Type F-250-C (Range 5 only) 61(7) Non -threaded Instrument flange (Range 1-4 only) www.rosemount.com 11 Rosemount 3051 February 2013 Table 2. 3051T In -Line Pressure Transmitter Ordering Information * The Standard offering represents the most common options. The starred options (*) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Isolating Diaphragm Process Connection Wetted Parts Material Standard Standard 2(8) 316L SST 316L SST 3(8) Alloy C-276 Alloy C-276 Sensor Fill Fluid Standard Standard 1 Silicone 2(7) Inert Housing Material Conduit Entry Size Standard Standard A Aluminum 1h-14 NPT B Aluminum M20 x 1.5 I SST lh-14 NPT K SST M20 x 1.5 P(9) Engineered polymer No conduit entries Expanded D Aluminum G1h M SST Glh Wireless options (RequiresWireIessoutputcode XandEngineeredPolymer housingcode P) Wireless Transmit Rate, Operating Frequency and Protocol Standard Standard WA3 User Configurable Transmit Rate, 2AGHz WirelessHART Antenna and SmartPower Standard Standard WP5 Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately) Options (Include with selected model number) PlantWeb Control Functionality Standard Standard A01 I FOUNDATION fieldbus Advanced Control Function Block Suite PlantWeb Diagnostic Functionality Standard Standard DA000)(17) Power Advisory HART Diagnostic DO1 FOUNDATION fieldbus Diagnostics Suite Integral Assembly Standard Standard S501i I Assemble to Rosemount 306 integral Manifold Diaphragm Seal Assemblies Standard Standard S1 i1 1> I Assemble to one Rosemount 1199 seal Mounting Bracket(12) Standard Standard B4 I Bracket for 2-in. Pipe or Panel Mounting, All SST 12 www.rosemount.com Rosemount 3051 February 2013 Specifications Performance Specifications This product data sheet covers HART, Wireless, FOUNDATION fieldbus, and PRO FIBUS PA protocols unless specified. Conformance To Specification (±3a (Sigma)) Technology leadership, advanced manufacturing techniques and statistical process control ensure specification conformance to at least ±3a. Reference Accuracy Stated reference accuracy equations include terminal based linearity, hysteresis, and repeatability. For Wireless, FOUNDATION fieldbus and PROFIBUS PA devices, use calibrated range in place of span. Models Standard 3051 3051C Ranges 2-5 ±0.065% of span For spans less than 10:1, accuracy = ±[0.015 + 0.005(S aL % of Span p Range 1 ±0.10%of span For spans less than 15:1, accuracy = ±[0.025 + 0.005(S a��] % of Span p ±0.10% of span Range 0 (CD) For spans less than 2:1, accuracy = ±0.05% of URL 3051 CA ±0.065%of span Rangesl-4 For spans less than 10:1, accuracy= ±[0.0075(Spa,)]% of Span 3051T ±0.065%of span Rangesl-4 For spans less than 10:1, accuracy = ±[0.0075(SpaL]% of Span Ranges ±0.075%of span ±0.075% of span 3051 L For spans less than 10:1, Ranges 2-4 accuracy= ±[0.025 + 0.005(S a��] % of Span p (1) High accuracy option P8 is not required for the Enhanced 3051. Rosemount 3051 with P80 ) Ranges 2-5 High Accuracy Option, P8 ±0.04% of span For spans less than 5:1, accuracy = +40.015 + 0.005(S a��] % of Span p Enhanced 3051 and WirelessHART ± 0.04% of span For spans less than 10:1 accuracy = +40.015 + 0.005(URL S pan)] % of Span ± 0.10% of span For spans less than 15:1 NA accuracy = ±[0.025 + 0.005(S a��] % of Span p ± 0.10% of span NA For spans less than 2:1 accuracy = + 0.05% of URL Ranges 2-4 High Accuracy Option, P8 ±0.04% of span For spans less than 5:1, accuracy= ±[0.0075(URL _ I]% of Span p Ranges 2-4 High Accuracy Option, P8 ±0.04% of span For spans less than 5:1, accuracy= +[0.0075(URL I% of Span p NA NA ± 0.04% of span For spans less than 10:1 accuracy = ±[0.0075(URL S pan)]% of Span ± 0.04% of span For spans less than 10:1 accuracy = ±[0.0075(URL S pan)]% of Span ± 0.075% of span ± 0.075% of span For spans less than 10:1 accuracy = +40.025 + 0.005(URL S pan)] % of Span 42 www.rosemount.com February 2013 Rosemount 3051 Flow Performance - Flow Reference Accuracy 3051 CFA Annubar Flowmeter (for 3051 and enhanced 3051) Ranges 2-3 I I ±1.80% of Flow Rate at 8:1 flow turndown 3051 CFC—A Compact Annubar Flowmeter — Annubar Option A Uncalibrated ±2.10% of Flow Rate at 8:1 flow turndown Ranges 2 3 I Calibrated +1.80% of Flow Rate at 8:1 flow turndown 3051 CFC Compact Orifice Flowmeter — Conditioning Option C ±1.75% of Flow Rate at 8:1 flow turndown Ranges 2 3 ±1.95% of Flow Rate at 8:1 flow turndown 3051 CFC Compact Orifice Flowmeter — Orifice Type Option PM ±2.00% of Flow Rate at 8:1 flow turndown Ranges 2-3 Q =0.65 ±2.00% of Flow Rate at 8:1 flow turndown 3051 UP Integral Orifice Flowmeter R <0.1 ±3.00% of Flow Rate at 8:1 flow turndown 0.1 <(3 <0.2 ±1.95% of Flow Rate at 8:1 flow turndown Ranges 2-3 10.2<p <0.6 ±1.75% of Flow Rate at 8:1 flow turndown 0.6<(3 <0.8 ±2.15% of Flow Rate at 8:1 flow turndown (1) For smaller line sizes, see Rosemount Compact Orifice Total Performance Total Performance is based on combined errors of reference accuracy, ambient temperature effect, and static pressure effect at normal operating conditions (70% of span typical reading, 740 psi (51 bar) line pressure). IFor±50 T (28 °C) temperature changes; 0-100%relative humidity, from 1:1 to 5:1 rangedown Models 3051 Standard Enhanced 3051 13051 C 3051T Ranges2-5 ±0.15%ofspan ±0.14%ofspan Rangesl-4 ±0.15%ofspan ±0.14%ofspan Long Term Stability Models I Long Term Stability (for 3051 and enhanced 3051) 3051 C ±0.125% of URL for 5 years Ranges 2 5 ±50 °F (28 °C) temperature changes, and up to 1000 psi (6.9 MPa) line pressure. 3051 CD, 3051 CG Low/Draft Range Ranges 0-1 ±0.2% of URL for 1 year 3051 CA Low Range +0.125% of URL for 5 years Range 1 ±50 °F (28 °C) temperature changes, and up to 1000 psi (6.9 MPa) line pressure. 3051 T ±0.125% of URL for 5 years Ranges 1 5 ±50 °F (28 °C) temperature changes, and up to 1000 psi (6.9 MPa) line pressure. www.rosemount.com 43 Rosemount 3051 Dynamic Performance 4 - 20 mA HARV l Total Response Time (Td + Tc)(2). 3051 C, Ranges 2-5: 100 ms Range 1: 255 ms Range 0: 700 ms 3051T: 100 ms 3051 L: See Instrument Toolkit® (Dead Time (Td) 45 ms (nominal) Update RateM 22 times per second FOUNDATION fieldbus and PROFIBUS PA protocols(3) 152 ms 307 ms N/A 152 ms See Instrument Toolkit 97 ms 22 times per second (1) Dead time and update rate apply to all models and ranges; analog output only (2) Nominal total response time at 75 OF (24 °C) reference conditions. (3) Transducer block response time, Analog Input block execution time not included. (4) Does not apply to wireless (output Code X). See "Wireless (Output Code X)" on page 48 for wireless update rate. February 2013 Typical HART Transmitter Response Time Transmitter Output vs. Time Pressure Released Td = Dead Time LI-Td r� To = Time Constant 100% Response Time = Td+T° 368% .......................... ;................... 632%of Total Step Change o% Time Line Pressure Effect per 1000 psi (6,9 MPa) For line pressures above 2000 psi (13,7 MPa) and Ranges 4-5, see user manual (Document number 00809-0100-4007 for enhanced 3051 HART, 00809-0100-4001 for HART, 00809-0100-4100 for WirelessHART 00809-0100-4774 for FOUNDATIONT" fieldbus, and 00809-0100-4797 for PROFIBUS PA). Models I Line Pressure Effect (for 3051 and enhanced 3051) 3051 CD, 3051 CF Zero Error Ranges 2-3 ±0.05% of URL/1000 psi (68.9 bar) for line pressures from 0 to 2000 psi (0 to 13.7 MPa) Range 1 ±0.25% of URL/1000 psi (68.9 bar) Range 0 ±0.125%of URL/100 psi (6.89 bar) Span Error Ranges 2-3 ±0.1 %of reading/1000 psi (68.9 bar) Range 1 ±0.4%of reading/1000 psi (68.9 bar) Range 0 ±0.1 5% of reading/1 00 psi (6.89 bar) Ambient Temperature Effect per 50°F (28°C) Models Ambient Temperature Effect (for 3051 and enhanced 3051) 3051 C Ranges 2-5 ±(0.01 25% URL + 0.0625% span) from 1:1to5:1 ±(0.025% URL+ 0.125%span) from 5:1 to 150:1 Range 1 ±(0.1 % URL + 0.25% span) from 1:1 to 30:1 Range ±(0.25% URL + 0.05% span) from 1:1 to 30:1 3051 CA Ranges 1-4 ±(0.025% URL + 0.125% span) from 1:1 to 30:1 ±(0.035% URL+ 0.125%span) from 30:1 to 150:1 3051 T Range 2 4 ±(0.025% URL+ 0.125%span) from 1:1 to 30:1 +(0.035% URL+ 0.125%span) from 30:1 to 150:1 Range 1 ±(0.025% URL+ 0.125%span) from 1:1 to 10:1 ±(0.05%URL+0.125%span) from 10:1 to 150:1 Range 5 ±(0.1 % URL + 0.15% span) 3051 L See Instrument Toolkit software. Mounting Position Effects Models Mounting Position Effects (for 3051 and enhanced 3051) 3051 C Zero shifts up to ±1.25 inH2O (3.11 mbar), which can be calibrated out. No span effect. 3051 CA, 3051 T Zero shifts up to 2.5 inH2O (6.22 mbar), which can be calibrated out. No span effect. With liquid level diaphragm in vertical plane, zero shift of up to 1 inH2O (2.49 mbar). With diaphragm in 3051 L horizontal plane, zero shift of up to 5 inH2O (12.43 mbar) plus extension length on extended units. All zero shifts can be calibrated out. No span effect. 44 www.rosemount.com Rosemount 3051 February 2013 Functional Specifications Service Liquid, gas, and vapor applications Range and Sensor Limits Table 7.3051 CD, 3051 CG, 3051 CF, and 3051 L Range and Sensor Limits Minimum Span Range and Sensor Limits Lower (LRL) c 3051 CD, 3051 CG, Upper 3051CD Differential 3051 CF, 3051 L (URL) 3051 CF Flowmeters 3051 CG Gage0) 3051 L Differential 3051 LGage(l ) 0777 0.10 inH2O 3.00 inH2O -3.00 inH2O NA NA NA (0,25 mbar) (25,00 mbar) (-7,47 mbar) 10) 0.50 inH2O 25.00 inH2O -25.00 inH2O -25.00 inH2O NA NA (1,2 mbar) (62,16 mbar) (-62,1 mbar) (-62,1 mbar) 2(') 1.67 inH2O 250.00 inH2O -250.00 inH2O -250.00 inH2O -250.00 inH2O -250.00 inH2O (4,14 mbar) (621,60 mbar) (-0,62 bar) (-0,62 bar) (-621,60 bar) (-621,60 bar) 3(') 6.67 inH2O 1000.00inH2O -1000.00 inH2O 0.50 psia-1000.00 inH2O 0.50 psia (16,58 mbar) (2,49 bar) (-2,49 bar) (34,47 mbar abs) (-2,49 bar) (34,47 mbar abs) 4k') 2.00 psi 300.00 psi -300.00 psi 0.50 psia -300.00 psi 0.50 psia (137,90 mbar) (20,68 bar) (-20,68 bar) (34,47 mbar abs) (-20,68 bar) (34,47 mbar abs) 50) 13.33 psi 2000.00 psi - 2000.00 psi 0.50 psia NA NA (919,30 bar) (137,90 bar) (-137,90 bar) (34,47 mbar abs) (1) Assumes atmospheric pressure of-14.7psig. (2) Range 0 only available with 3051 CD. Range 1 only available with 3051 CD, 3051 CG, or 3051 CF. Range 5 not available with 3051 L Differential and 3051 Gage. (3) inH20 referenced at 68 degrees Fahrenheit. Table 8. 3051 CA and 3051 T Range and Sensor Limits 3051 CA 3051T Range and Sensor Limits qu Range and Sensor Limits Minimum Upper Lower Minimum Upper Lower Lower0) Span (URL) (LRL) Span (URL) F(LRL) (LRL) (Gage) 1 0.33 psia 30.00 psia 0 psia 1 0.33 psi 30.00 psi 0 psia -14.70 psig (20,68 mbar) (2,07 bar) (0 bar) (20,68 mbar) (2,07 bar) (0 bar) (-1,01 bar) 2 1.00 psia 150.00 psia 0 psia 2 1.00 psi 150.00 psi 0 psia -14.70 psig (68,95 mbar) (10,34 bar) (0 bar) (68,95 mbar) (10,34 bar) (0 bar) (-1,01 bar) 3 5.33 psia 800.00 psia 0 psia 3 5.33 psi 800.00 psi 0 psia -14.70 psig (367,27 bar) (55,16 bar) (0 bar) (367,27 mbar) (55,16 bar) (0 bar) (-1,01 bar) 4 26.6 psia 4000.00 psia 0 psia 4 26.67 psi 4000.00 psi 0 psia -14.70 psig (1,84 bar) (275,79 bar) (0 bar) (1,83 bar) (275,79 bar) (0 bar) (-1,01 bar) 5 2000.00 psi 10000.00 psi 0 psia -14.70 psig (137,90 bar) (689,48 bar) (0 bar) (-1,01 bar) (1) Assumes atmospheric pressure of 14.7 psig. 46 www.rosemount.com February 2013 Rosemount 3051 Power Module Field replaceable, keyed connection eliminates the risk of incorrect installation, Intrinsically Safe Lithium-thionyl chloride Power Module with PBT/PC enclosure. Ten-year life at one minute update rate.0) (1) Reference conditions are 70 OF (21 °C), and routing data for three addi- tional network devices. NOTE: Continuous exposure to ambient temperature limits of-40 OF or 185 OF (-40 °C or 85 °C) may reduce specified life by less than 20 per- cent. Overpressure Limits Rosemount 3051 CDJCGJCF • Range 0: 750 psi (51,7 bar) • Range 1: 2000 psig (137,9 bar) • Ranges 2-5: 3626 psig (250 bar) 4500 psig (310,3 bar) for option code P9 Rosemount 3051 CA • Range 1: 750 psia (51,7 bar) • Range 2: 1500 psia (103,4 bar) • Range 3: 1600 psia (110,3 bar) • Range 4: 6000 psia (413,7 bar) Rosemount 3051 TGITA • Range 1: 750 psi (51,7 bar) • Range 2: 1500 psi (103,4 bar) • Range 3: 1600 psi (110,3 bar) • Range 4: 6000 psi (413,7 bar) • Range 5: 15000 psi (1034,2 bar) For 3051 L or Level Flange Option Codes FA, FB, FC, FD, FP, and FQ, limit is 0 psia to the flange rating or sensor rating, whichever is lower. Table 9.3051 Land Level Flange Rating Limits Standard Type CS Rating SST Rating ANSI/ASME Class 150 285 psig 275 psig ANSI/ASME Class 300 740 psig 720 psig ANSI/ASME Class 600 1480 psig 1440 psig At 00 °F (38 °C), the rating decreases with increasing temperature, perANsl/ASME 816.5. DIN PN 10-40 40 bar I 40 bar DIN PN 10/16 16 bar 16 bar DIN PN 25/40 40 bar 40 bar At 248 °F (120 °C), the rating decreases with increasing temperature, per DIN 2401 Static Pressure Limit Rosemount 3051 CD Only Operates within specifications between static line pressures of 0.5 psia and 3626 psig (4500 psig (310, 3 bar) for Option Code P9). Range 0: 0.5 psia and 750 psig (3,4 bar and 51, 7 bar) Range 1: 0.5 psia and 2000 psig (3, 4 bar and 137, 9 bar) Burst Pressure Limits 3051 C, 3051 CIF Coplanar or Traditional process flange 10000 psig (69 MPa) 3051T Inline Ranges 1-4: 11000 psi (75,8 MPa) Range 5: 26000 psig (179 MPa) Failure Mode Alarm HART 4-20 mA (Output option Code A) If self -diagnostics detect a sensor or microprocessor failure, the analog signal is driven either high or low to alert the user. High or low failure mode is user -selectable with a jumper/switch on the transmitter. The values to which the transmitter drives its output in failure mode depend on whether it is configured to standard, NAMUR-compliant, or custom levels (see Alarm Configuration below). The values for each are as follows: High Alarm Low Alarm Default >_ 21.75 mA < 3.75 mA NAMUR compliantU) >_ 22.5 mA < 3.6 mA Custom levelsk`) 20.2 - 23.0 mA 3.4 - 3.8 mA (1) Analog output levels are compliant with NAMUR recommendation NE 43, see option codes C4 or C5. (2) Low alarm must be 0.1 mA less than low saturation and high alarm must be 0.1 mA greaterthan high saturation. If the device is configured for HART7 Revision 7, failure information will be passed as a status along with the Process Variable. Output Code F, W, and X If self -diagnostics detect a gross transmitter failure, that information gets passed as a status along with the process variable. Temperature Limits Ambient -40 to 185 °F (-40 to 85 °C) With LCD display0) M: -40 to 175 °F (-40 to 80 °C) (1) For the standard 3051, LCD display may not be readable and LCD updates will be slower at temperatures below -22 °F (-30 °C). (2) Wireless LCD display may not be readable and LCD updates will be slower at temperature below -4 °F (-20 °C). Storageil i -50 to 230 °F (-46 to 110 °C) With LCD display: -40 to 185 °F (-40 to 85 °C) With Wireless Output: -40 °F to 185 °F (40 °C to 85 °C) (1) If storage temperature is above 85°C, perform a sensor trim prior to installation. www.rosemount.com 49 Lr) MODEL - 50-01 Pressure Relief & Pressure Sustaining Valve • Accurate Pressure Control • Optional Check Feature • Fast Opening to Maintain Line Pressure • Slow Closing to Prevents Surges • Completely Automatic Operation The Cla-Val Model 50-01 Pressure Relief Valve is actuated by line pressure through a pilot control system, opening fast to maintain steady line pressure but closing gradually to prevent surges. Operation is completely automatic and pressure settings may be easily changed. This valve can be used for pressure relief, pressure sustaining, back pressure, or unloading functions in a bypass system. Schematic Diagram If a check feature is added, and a pressure reversal occurs, the Item Description downstream pressure is admitted into the main valve cover chamber, 1 100-01 Hytrol Main Valve closing the valve to prevent return flow. 2 X42N-2 Strainer & Needle Valve F\ 3 CRL-60 Pressure Relief Control REMOTE SENSING A' Optional Features Item Description z B CK2 Isolation Valved "— 5 D Check Valves with Isolation Valve °' Pz F Remote Pilot Sensing P1 H Drain to Atmosphere O F� III I ID1/ -? Bz M X144 e-FlowMeter Tw °Z B G3� P X141 Pressure Gauge \-- TO S CV Speed Control (Opening) GRAIN ATMOSPHEE RE V X101 Valve Position Indicator see page 3 for INLET approvals l Typical Applications Pressure Relief Service Pressure Sustaining Service This fast opening, slow closing relief valve provides sys- When installed in a line between an upper zone and a lower area tem protection against high pressure surges on pump of heavy demand, the valve acts to maintain desired upstream start up and pump shut down by dissipating the excess pressure to prevent "robbing" of the upper zone. Water in excess pressure to a safe location. of pressure setting is allowed to flow to an area of heavy demand, control is smooth, and pressure regulation is positive. Q�1 Pump o CLA-VAL 50-01/650-01 Pressure Sustaining Valve \ 60-11 Y� _\Isolation Valve Booster Booster Pump Control Valve Service Upper Zone s X43H Strainer Isolation Valve CLA-VAL 50-01/650-01 Pressure Relief Pressure Sustaining Valve Area Of Heavy Demand Model 50-01 (Uses 100-01 Hytrol Main Valve) Pressure Ratings (Recommended Maximum Pressure - psi) Pressure Class Valve Body &Cover Flanged Grooved Threaded Grade Material ANSI 150 300 300 End$ Standards' Class Class Class Details ASTM A536 Ductile Iron B16.42 250 400 400 400 ASTM A216-WCB Cast Steel B16.5 285 400 400 400 UNS 87850 Bronze B16.24 225 400 400 400 Note: ANSI standards are for flange dimensions only. Flanged valves are available faced but not drilled. $ End Details machined to ANSI B2.1 specifications. Valves for higher pressure are available; consult factory for details Materials Component Standard Material Combinations Body & Cover Ductile Iron Cast Steel Bronze Available Sizes 1" - 36" 1" - 16" 1" - 16" 25 - 900mm 25 - 400mm 25 - 400mm Disc Retainer & Cast Iron Cast Steel Bronze Diaphragm Washer Trim: Disc Guide, Bronze is Standard Seat & Cover Bearing Stainless Steel is Optional Disc Buna-N® Rubber Diaphragm Nylon Reinforced Buna-N® Rubber Stem, Nut & Spring Stainless Steel For material options not listed, consult factory. Cla-Val manufactures valves in more than 50 different alloys. Model 50-01 Dimensions (In Inches) Valve Size (Inches) 1 1 t/4 1 t/2 2 A Threaded 7.25 7.25 7.25 9.38 AA 150 ANSI - - 8.50 9.38 --------------- AAA 300 ANSI ---------- -------- - -------- -------- - -------- -- 9.00 -------- ---- 10.00 -------- AAAA Grooved End - - 8.50 9.00 -------- B Diameter --- --- 5.62 -- 5.62 5.62 6.62 ---------------- C Maximum - 5.50 5.50 5.50 6.50 ----------------------- CC Maximum Grooved End --- -- - - --- --- - --- -- -- 4.75 -------- ----- -- 5.75 -------- D Threaded 3.25 3.25 3.25 4.75 ---------------- DD150ANSI - - -- - -------- 4.00 -------- 4.75 DDD 300 ANSI - - 4.25 5.00 ------------- DDDD Grooved End --- - ---- - --- - ---- - -------- - -------- 4.75 ------- E -------- 1.12 -------- 1.12 -------- 1.12 -------- 1.50 -------- --------------------------- EE Grooved End -------- - -------- - -------- 2.00 2.50 --------------------------- F 150 ANSI --- --- - -- - 2.50 3.00 --------------------------- FF 300 ANSI -------- - -------- - -------- 3.06 -------- 3.25 ----------- G Threaded -------- 1.88 -------- 1.88 -------- 1.88 -------- 3.25 --------------------------- GG 150 ANSI - - - - - 4.00 - - 3.25 ------------------ GGG 300 ANSI --- --- - -- - 4.25 3.50 --------------------------- GGGG Grooved End -------- - -------- - -------- - -------- 3.25 -------------- H NPT Body Tapping -------- 0.375 -------- 0.375 -------- 0.375 -------- 0.375 JNPT Cover Center Plug 0.25 0.25 0.25 0.50 KNPTCoverTapping 0.375 0.375 0.375 0.375 Stem Travel 0.40 0.40 0.40 0.60 Approx. Ship Weight (lbs) ----- 15 ------- 15 -- -- 15 -------- 35 Approx. X Pilot System 11 11 11 13 Approx. Y Pilot System 9 9 9 9 Approx. Z Pilot System 9 9 9 9 ---------------------------------- B (Diameter) 100-01 Threaded & K 1 Flanged A'�( H I C MAX) Inlet Outlet - io--- - --0- r--, G E F FF GGG + v Inlet For sizes 18 - 36-inches, use 50-66 E-Sheet Inlet � D A DDD~ AA AAA -------------------------------------I B (Diameter) 100-01 �j Grooved AK X rn CC (MAX) EE ir Inlet i-DDDD- AAAA I O i O Y OHO _ z ................i.....................1... 2 V2 3 4 6 8 10 12 14 16 18 20 24 30 36 11.00 12.50 - - - - - - - - - - - - 11.00 - 12.00 --- -- 15.00 --- -- 20.00 --- -- 25.38 --- -- 29.75 --- -- 34.00 --- -- 39.00 --- -- 41.38 --- --- 46.00 --- -- 52.00 --- -- 61.50 --- -- 63.00 --- --- 72.75 -------- 11.62 -------- -------- 13.25 -------- - 15.62 -------- - 21.00 -------- - 26.38 -------- - ----- 31.12 -------- -- - 35.50 -------- - ---- 40.50 -------- -- 43.50 -------- - 47.64 -------- -- ---- 53.62 -------- -------- 63.24 -------- -------- 64.50 -------- -------- 74.75 -------- 11.00 12.50 15.00 20.00 25.38 - - - - - - - - - 8.00 9.12 11.50 15.75 20.00 23.62 28.00 32.75 35.50 41.50 45.00 53.16 56.00 66.00 T56 8.19 10.62 13.38 16.00 17.12 20.88 24.19 25.00 39.06 41.90 43.93 54.60 59.00 6.88 -------- -- 7.25 -------- -------- 9.31 -------- -- ---- 12.12 -------- --- - 14.62 -------- -------- - -------- -- - - ---- - ---- - -- - - - - - - - -------- - 5.50 6.25 - - - - - - - - - - - - 5.50 6.00 7.50 10.00 12.69 14.88 17.00 19.50 20.81 - - 30.75 - - 5.88 6.38 7.88 10.50 13.25 15.56 17.75 20.25 21.62 - - 31.62 - - ------ ------ 6.00 ---- - 7.50 ------ --- - -- ------ --- - -- ------ --- - -- ------ --- - -- ------ --- - -- ------ 1.69 -------- 2.06 -------- 3.19 --- -------- 4.31 -- -------- 5.31 ---- -------- 9.25 -------- 10.75 -- -------- 12.62 -------- 15.50 -------- -------- 12.95 -------- -------- 15.00 - -------- 17.75 -------- 21.31 -------- 24.56 -------- ----- -- 2.88 -- -- 3.12 4.25 6.00 -- 7.56 -------- - - - -- ---- - - - - - - -------- - - 3.50 3.75 4.50 5.50 6.75 8.00 9.50 10.50 11.75 15.00 16.50 19.25 22.50 28.50 3.75 4.13 5.00 6.25 7.50 8.75 10.25 11.50 12.75 15.00 16.50 19.25 24.00 30.00 -------- 4.00 -------- 4.50 -------- - --- -------- - ---- - - - - - - - -------- - - - -------- 4.00 4.00 -- 5.00 --- -- 6.00 --- -- 8.00 --- -- 8.62 --- -- 13.75 --- .. 14.88 -- 15.69 -------- - - --- -- 22.06 -------- - - 4.31 4.38 5.31 6.50 8.50 9.31 14.50 15.62 16.50 - - 22.90 - - -------- - -------- 4.25 -------- 5.00 -------- - -------- - -------- - -------- - -------- - ---- - - - - - - --- --- 0.50 ----- -- 0.50 ---- -- 0.75 -------- -------- 0.75 -------- 1.00 -------- -------- 1.00 1.00 -------- --- --- 1.00 --- -- 1.00 -------- -------- 1.00 -------- 1.00 -------- ----------------- 1.00 2.00 -------- 2.00 -------- -------- 0.50 -------- 0.50 0.75 -------- 0.75 1.00 ------- 1.00 1.25 -------- 1.50 2.00 -------- 1.00 1.00 ----------------- 1.00 2.00 2.00 -------- 0.50 -------- 0.50 -------- 0.75 -------- 0.75 -------- 1.00 -------- 1.00 -------- 1.00 -------- 1.00 -------- 1.00 -------- 1.00 -------- 1.00 ----------------- 1.00 2.00 -------- 2.00 -------- 0.70 -------- 0.80 -------- 1.10 -------- 1.70 -------- 2.30 -------- 2.80 -------- 3.40 -------- 4.00 -------- 4.50 -------- 5.10 -------- 5.63 ----------------- 6.75 7.50 -------- 8.50 -------- 50 -------- 70 -------- 140 -------- 285 -------- 500 -------- 780 ---- --- 1165 -------- 1600 -------- 2265 -------- 2982 -------- 3900 ----------------- 6200 7703 ---- 11720 14 15 17 29 31 33 36 40 40 43 47 68 79 85 ----- -- -------- ---12 -- ---20 -- ---22 -- ---24 -- ----- -- 26 ---2- -- ---3- -- ----- -- ----- -- -----------40 -- ----- -- ----- -- -------- ---12 -- ---20 -- ---22 -- ---24 -- ---26 -- ---29 -- ---30 -- ---32 -- ---34 -- ---39------42 -- ---47 -- 100-01 Pattern: Globe (G), Angle (A), End Connections: Threaded (T), Grooved (GR), Flanged (F) Indicate Available Sizes 50-01 Valve Inches 1 11/4 11/2 2 2'F 3 4 6 8 10 12 14 16 18 20 24 30 36 Selection mm 25 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600 750 900 Pattern G, A G, A G, A G, A G, A G, A G, A G, A G, A G, A G, A G, A G, A G G G, A G G Basic Valve 100-01 T, F, T, F, T, F, T, F, F, F, F, End Detail T T Gr' Gr Gr' Gr Gr Gr' F F F F F F F F F Gr' Suggested Maximum 55 93 125 210 300 460 800 1800 3100 4500 7000 8400 11000 14000 17000 25000 42000 50000 Flow (gpm) Maximum 120 210 280 470 670 1000 1800 4000 7000 11000 16000 15000 25000 31000 35000 56500 63000 85000 Surge Suggested Maximum 3.5 6 8 13 19 29 50 113 195 309 442 530 694 883 1073 1577 2650 3150 Flow (Liters/Sec) Maximum 7.6 13 18 30 42 63 113 252 441 693 1008 1197 1577 1956 2461 3560 3975 5360 Surge 100-01 Series is the full internal port Hytrol. 'Globe Grooved Only Notes: • For sizes 18 through 36-inches / 450mm though 900 mm, use 50-66 E-Sheet • Many factors should be considered in sizing pressure relief valves including inlet pressure, outlet pressure and flow rates. • For sizing questions or cavitation analysis, consult Cla-Val with system details. Pilot Systern Specifications Adjustment Ranges Valve Options When Ordering, Specify: p 0 to 75 psi Max. 1. Catalog No. 50-01 20 to 105 psi 2. Valve Size X141 Pressure 20 to 200 psi ' 3. Pattern - Globe or Angle Gauge 100 to 300 psi 4. Pressure Class 0—v "Supplied unless otherwise speci- 5. Threaded, Flanged, Grooved fled. Other ranges are 6. Trim Material available, please consult factory. 7• Adjustment Range �l Temperature Range 8. Desired Options I --I Water: to 180°F 9. When Vertically Installed Main Valve Options Materials EPDM Rubber Parts Standard Pilot Sv_ stem Materials Optional diaphragm, disc and o-ring X101 AR Valve X101 Pilot Control: Low Lead Bronze fabricated with EPDM synthetic rub- Position Indicator Valve Position Trim: Stainless Steel Type 303 ber with Air Release Indicator Rubber: Buna-N° Synthetic Rubber Viton® Rubber Parts - suffix KB Optional diaphragm, disc and o-ring fabricated with Viton° synthetic rubber Optional Pilot Svstem Materials Pilot Systems are available with optional Epoxy Coating - suffix KC Aluminum, Stainless Steel or Monel materials. NSF 61 Listed and FDA approved, X144 e-FlowMeter / fusion bonded epoxy coating Dura-Kleen® Stem - suffix KD Fluted design prevents dissolved min- erals build-up on the stem Pilot Appraif2liz nISFIA tell 372m National LFS Trim Designed to regulate precisely and pND CE Tm smoothly at typical flow rates as well as "Reduction of Laad lower than the industry standard of 1 �oDrinking Water fps, without decreasing the valve's X43H Strainer Stainless Steel Pilot capacity CLA_� A� 1701 Placentia Ave • Costa Mesa CA 92627 • Phone: 949-722-4800 • Fax: 949-548-5441 • E-mail: info@cla-val.com • www.cla-val.com Y "'Copyright Cla-Val 2017 • Printed in USA • Specifications subject to change without notice. E-50-01 (R-01/2017) Section 5.2 Check Valve Silent Operation Proven Performance Cost Effective Bulletin 1400/1800 .#A LKAT I C� Silent Check Valves www.valmatic.com Certified Lead -Free NSF/ANSI 61 & 372 Certified Installation Dimensions FLOW Series 1800 - Globe Note: Valves 2'/2 (65 mm) - 10 in. (250mm) mate to wafer style butterfly valves without the use of spool pieces. " ;_ Z,,� r- Butterfl U Flanges conform to ANSI B16.1 Class 125 or 250 or ISO 7005 PN10 or PN16 Dimensions - Inch Dimensions - Metric Valve CWP ANSI Weight Valve CWP PN Weight Size (psig) Class A B C D (lb) Size (Bar) Class A B C D (kg) 200 125 7.00 5.50 5.50 0.69 19 21/2 65 16 10/16 178 140 145 18 9 400 250 7.50 5.50 5.88 1.00 30 200 125 7.50 6.00 6.00 0.94 28 3 80 16 10/16 192 152 160 24 13 400 250 8.25 6.00 6.63 1.13 36 200 125 9.00 7.25 7.50 0.94 43 4 100 16 10/16 220 184 180 24 20 400 250 10.00 7.25 7.88 1.25 59 200 125 10.00 8.50 8.50 0.94 55 5 125 16 10/16 250 216 210 24 25 400 250 11.00 8.50 9.75 1.38 78 200 125 11.00 9.75 9.50 1.00 78 6 150 16 10/16 285 248 240 25 35 400 250 12.50 9.75 10.63 1.44 103 200 125 13.50 12.50 11.75 1.13 102 16 10 340 318 295 29 46 8 200 400 250 15.00 12.50 13.00 1.63 179 16 16 340 318 295 29 81 200 125 16.00 15.50 14.25 1.19 208 16 10 395 362 350 30 94 10 250 400 250 17.50 15.50 15.25 1.88 253 16 16 405 362 355 30 114 200 125 19.00 14.25 17.00 1.25 294 16 10 445 394 400 32 133 12 300 400 250 20.50 14.25 17.75 2.00 401 16 16 460 394 410 32 181 150 125 21.00 15.75 18.75 1.38 380 10 10 505 400 460 35 172 14 350 300 250 23.00 15.75 20.25 2.13 511 16 16 520 400 470 35 231 150 125 23.50 17.63 21.25 1.44 501 10 10 565 448 515 37 227 16 I 400 300 250 25.50 17.63 22.50 2.25 697 16 16 580 448 525 37 316 150 125 25.00 18.75 22.75 1.56 724 10 10 615 476 565 40 328 18 450 300 250 28.00 18.75 24.75 2.38 959 1 16 16 640 476 585 40 434 150 125 27.50 20.63 25.00 1.69 890 10 10 670 524 620 43 403 20 500 300 250 30.50 20.63 27.00 2.50 1,180 16 16 715 524 650 43 535 150 125 32.00 24.00 29.50 1.88 1,220 10 10 780 610 725 48 553 24 600 300 250 36.00 24.00 32.00 2.75 1,680 16 16 840 610 770 48 762 150 125 38.75 29.25 36.00 2.13 2,100 30 300 250 43.00 29.25 39.25 3.00 2,700 150 125 46.00 45.00 42.75 2.38 4,400 36 300 250 50.00 46.00 46.00 3.38 5,100 150 125 53.00 50.00 49.50 2.63 7,200 42 300 250 57.00 50.00 52.75 3.69 7,900 5 Valve Construction PRESSURE RATINGS MAXIMUM PRESSURE RATINGS SERIES DESCRIPTION SIZE RANGE END CONNECTION CWP psig (Bar) 1400THR Threaded 1/2" - 2" Threaded 250 (15-50mm) NPT (17.2) 2" - 6" Wafer 400 (50-150mm) Class 125/250 (27.6) 1400A Wafer Style 8" - 10" Wafer 200 (200-250mm) Class 125 (13.8) 8" - 10" Wafer 400 (200-250mm) Class 250 (27.6) 2 1/2" - 12" Flanged 200 (65-250mm) Class 125 (13.8) 14" - 42" Flanged 150 (300-1050mm) Class 125 (10.3) 1800 Globe Style 2 1/2" - 12" Flanged 400 (65-250mm) Class 250 (27.6) 14" - 42" Flanged 300 (300-1050mm) Class 250 (20.7) Headloss Chart Wafer Style CUBIC METERS PER HOUR 000 Nf.O 0 Silent Check Valve O 5 1 1 - q 1r 2° 21d' 3„ 4„ 5" I 6' 8" 1,0', -3 1c 8 W_ 8 7 J10 FEET/SECOND 2 LU 7 LU 6 f VELOCITY 6 5 3: 5 >Q of 1 O t V Q 3 Q Q LL 3 LU W 2 UQ� 7V -.7 LL -.6 O W j LL 2 Q LL _.5 Z U C� Z - .4 it rn N rn 4 FVELOCITY D W LU u) ^ Q 1 V I '3 O 1 J .8 I- .8 I 1 2 .6 5 C I .q .3 1 \O - .08 N C) V 3 FLOW OF WATER IN GALLONS PER MINUTE MATERIALS OF CONSTRUCTION Threaded Style COMPONENT I STANDARD Body Lead -Free Bronze Disc Lead -Free Bronze Seat Teflon Spring T316 Stainless Steel IWafer & Globe Style COMPONENT I STANDARD I OPTIONAL Body Cast Iron Stainless Steel Ductile Iron Disc Lead -Free Bronze AI -Bronze (Lead -Free) Stainless Steel Seat Lead -Free Bronze AI -Bronze (Lead -Free) Stainless Steel Resilient Seat _ Buna-N EPDM Spring T316 Stainless Heavy Duty Spring Steel Globe Style CUBIC METERS PER HOUR 0 0 0 000000 0 o S oSao 0 5 4 3 2 w LU 1 Q 8 '7 LL .6 0 .5 (n .4 of LLI H 3 2 .2 .1 N CJ V NCO OrW O O 0 0000 .08 N th V NiO�W FLOW OF WATER IN GALLONS PER MINUTE Size 1 2 2-112 3 1 4 1 5 1 6 1 8 1 10 1 12 1 14 1 16 1 18 1 20 1 24 1 30 1 36 1 42 Wafer Cv 43 88 130 228 1 350 1 520 1 900 1450 - - I - I - I - - - Globe Cv - 127 155 278 1 435 1 625 1115 1770 2500 3400 4400 1 5600 1 6900 10,000 15,400 22,400 30,400 r1 FORTWORTH MEMORANDUM Date: October 26, 2023 To: Dana Burghdoff, Assistant City Manager From: Chris Harder, P.E. Water Director Subject: Emergency Purchase of Skid Mounted Booster Pumping Station The Water Department requests approval of an emergency procurement and expenditure to purchase a skid mounted booster pump station to be located at the Harmon Road Elevated Storage Tank site that would be used to meet upcoming summer demands in the Northside III pressure plane. In summer, 2023, peak water demands within the Northside III pressure plane came dangerously close to matching existing delivery capacity. Had that happened, we would have had to request voluntary restrictions from our wholesale and retail customers, or run the risk of draining water tanks, which would trigger a boil water notice and impact fire protection. The Utility has several capacity improvement projects that are in design, but will take several years to construct. In order to meet anticipated Northside III water demands for the summer of 2024, an emergency procurement of a skid mounted booster pump station is required, due to the lead times needed by a vendor to compile, assemble, and deliver a complete booster pumping assembly. This pumping equipment would allow the Water Department to transfer 8 million gallons per day to the Northside III pressure plane during times of extremely high water use. A skid mounted booster pump station assembly includes the suction and discharge pipe header, the pumps and motors, isolation and check valves, pressure transmitters, and a main power panel. Upon delivery to the site, utility staff will run electricity to the skid mounted power panel and connect the skid suction and discharge headers to existing piping. The majority of the field work for these connections will be performed while we are waiting on receiving the skid mounted pumping unit from the vendor, so that the pumping unit can be placed in service very quickly after delivery. The skid mounted pumping unit bid specifications and bid sheet are being submitted to the Purchasing Department concurrent with this memorandum. Purchasing will receive quotes from qualified vendors and the City will then issue a purchase order to the lowest qualified respondent. The cost estimate for the skid mounted booster pump is $750,000. This is an unbudgeted expenditure. This expenditure will be charged to 56001-0605004-5330201. An M&C will be prepared to ratify the purchasing contract with the vendor and appropriate funding. The expenditure will then be moved from operating to capital funding. Chapter 2, Article 1, Section 2-9 of the City of Fort Worth's Code of Ordinances and Section 252.022 of the Local Government Code defines emergency expenditures and, pursuant with Texas Local Government Code Chapter 252, exempts from normal bidding requirements expenditures that are necessary to preserve or protect public health or safety of the municipality's residents. If you have any additional questions, please contact Chris Harder at 817-392-5020. APPROVED FOR EMERGENCY PROCUREMENT: Recommended: Approved as to Form and Legality: Approve: ch is-i-0 her {fai de Christopher Harder (Oct 26, 2023 08:17 CDT) Christopher Harder, Water Director DBlack (Oct 27, 202317:02 CDT) Doug Black, Assistant City Attorney Yard 8� ¢eL� Dana Burghdoff (Oct 2023M11 CDT) Dana Burghdoff, Assistant City Manager